MIG and TIG Welding

MIG and TIG Welding: How Gas-Shielded Arc Welding Works

MIG and TIG welding are gas-shielded arc processes. Learn how each works, how they differ, what gases and equipment they use, and which to choose.

On this page
  1. The short answer
  2. What MIG welding is (GMAW, MAG and other names)
  3. How MIG welding works
  4. What TIG welding is (GTAW)
  5. How TIG welding works
  6. Shielding gas: what it does and what each process uses
  7. MIG vs TIG: how they compare
  8. Which one should you learn first?
  9. Where MIG and TIG sit among other arc welding processes
  10. Basic equipment for each
  11. Safety basics
  12. Next steps in this guide

The short answer

MIG and TIG welding are two arc welding processes that use a shielding gas to protect the molten weld from the air. In MIG welding, a spool of wire is fed continuously through a gun and becomes part of the weld. In TIG welding, a non-consumable tungsten electrode creates the arc, and the welder adds filler metal by hand when needed.

MIG is generally faster and easier to pick up. TIG is slower but gives more control and is often chosen for thin metal, tubing, stainless steel and aluminum where appearance and precision matter.

What MIG welding is (GMAW, MAG and other names)

MIG stands for metal inert gas. The formal name used in standards is gas metal arc welding (GMAW). You will also see:

  • MAG (metal active gas): used when the shielding gas contains an active component such as carbon dioxide or oxygen, which is common when welding steel. The term is widely used in Europe.
  • Wire welding or “wire feed welding”: an informal name that refers to the spool of wire.

In everyday use, most people call all of these “MIG,” even when the gas is technically active. The sections below use “MIG” in that sense.

In simple terms: you pull a trigger, wire feeds out of the gun, an arc forms between the wire and the metal, and shielding gas flows around the arc. MIG is common in automotive repair, general fabrication, trailers, gates and furniture, structural work and hobby projects.

How MIG welding works

A MIG setup has a few main parts:

  • A power source that holds a set voltage (a constant-voltage machine).
  • A wire feeder that pushes wire through a liner to the gun at an adjustable speed.
  • A gun with a contact tip that transfers current to the wire, and a nozzle that directs gas.
  • A gas cylinder, regulator and hose that supply shielding gas.
  • A work clamp that completes the electrical circuit.

When you pull the trigger, the wire and gas start together. The arc melts the wire and a small area of the base metal into a molten pool, which cools into the weld. Two main settings matter most: wire feed speed, which largely controls current and heat, and voltage, which affects arc length and bead shape. Our guide to good MIG settings gives starting points.

Related wire types exist as well. Metal-cored arc welding uses a tubular wire filled with metal powder in a similar setup, and flux-cored wire can be used with or without external gas.

What TIG welding is (GTAW)

TIG stands for tungsten inert gas; the formal name is gas tungsten arc welding (GTAW). The arc is struck between a tungsten electrode and the workpiece. Tungsten has a very high melting point, so the electrode is not consumed in normal use. If the joint needs filler, you feed a separate rod into the molten pool.

TIG is used on steel, stainless steel, aluminum and other metals. Common examples include bicycle frames, roll cages, exhaust work, food-grade stainless fabrication and aircraft-type tubing. For a specific example, see TIG welding chrome-moly tubing.

To answer a common question: yes, TIG welding works on steel. It also works well on stainless and aluminum, and it is often the first choice for those thinner or more demanding jobs.

How TIG welding works

A TIG setup includes:

  • A power source that provides a controlled current. DC is used for steel and stainless; AC is used for aluminum. Many machines offer both.
  • A torch holding a tungsten electrode in a collet, with a ceramic cup that directs argon.
  • A way to control current: a foot pedal, a thumb or finger control on the torch, or preset slopes. The torch switch can usually be used in 2T or 4T mode.
  • Argon (most commonly 100% argon) from a cylinder with a flowmeter.
  • Filler rod, held in the other hand.

You start the arc, wait for a molten pool to form, then dab or feed filler into the leading edge of the pool while moving along the joint. The choice of electrode matters; see choosing TIG tungsten. Aluminum has its own challenges, covered in how to TIG aluminum for beginners.

Shielding gas: what it does and what each process uses

Molten metal reacts with oxygen and nitrogen in the air. The result can be porosity (tiny holes), weak welds and heavy oxidation. Shielding gas pushes the air away from the weld area.

  • TIG typically uses pure argon. Some specialized jobs use argon mixed with helium.
  • MIG on mild steel commonly uses a mix of about 75% argon and 25% CO2 (often called C25), or in some cases 100% CO2.
  • MIG on aluminum typically uses pure argon.

Our MIG shielding gas guide compares these options in more detail. If your MIG welds look full of holes, see porosity in MIG welds.

MIG vs TIG: how they compare

MIG (GMAW) TIG (GTAW)
Electrode Continuously fed consumable wire Non-consumable tungsten
Filler The wire itself Separate rod, fed by hand
Speed Generally faster Generally slower
Learning curve Easier to start Takes more practice
Hands needed One on the gun Two (torch and filler), often a foot on the pedal
Control and appearance Good Very good when done well
Typical uses Fabrication, repair, thicker material Thin material, tubing, stainless, aluminum
Typical gas Argon/CO2 mixes, CO2 or argon Argon
Wind tolerance Low with gas shielding Low

Neither process is simply “better” (see our TIG vs MIG comparison). The right choice depends on the material, the thickness, the joint and how much finish quality you need.

Which one should you learn first?

Most beginners find MIG easier. It can be difficult to get perfect welds, but the process is forgiving: you hold the gun, pull the trigger, and the machine feeds the filler. TIG requires coordinating both hands (and often a foot), keeping a short arc and keeping the metal very clean.

A reasonable approach is to start with MIG if your projects are mostly steel fabrication, repair and general building. Choose TIG first if you know your work will be thin stainless, aluminum or tubing, and you are willing to practice patiently.

Where MIG and TIG sit among other arc welding processes

The “four types of arc welding” people often mention are usually:

  1. Shielded metal arc welding (SMAW), also called stick welding. In the UK and Australia this is often called MMA (manual metal arc).
  2. Gas metal arc welding (GMAW), or MIG.
  3. Flux-cored arc welding (FCAW), which uses a tubular wire with flux inside.
  4. Gas tungsten arc welding (GTAW), or TIG.

Submerged arc welding is another common arc process, usually seen in industrial settings. So “MMA and TIG” refers to stick welding and tungsten inert gas welding.

Basic equipment for each

For MIG, expect to need a MIG welder, gas cylinder and regulator (unless you use self-shielded flux-core wire), wire in the right diameter, a gun consumables kit, a work clamp and personal protective equipment.

For TIG, expect a TIG-capable machine (AC/DC if you want to weld aluminum), a torch with a gas lens or standard collet body, tungsten electrodes, filler rods, an argon cylinder with a flowmeter, and a foot pedal or other current control.

For either process you will also need a welding helmet, gloves, flame-resistant clothing, closed leather footwear, and tools for cleaning and cutting.

Safety basics

Welding involves intense ultraviolet and visible light, heat, sparks, fumes and electrical hazards. At a minimum:

  • Wear an approved welding helmet with a suitable shade and cover bare skin, since arc radiation can burn skin and eyes.
  • Weld with good ventilation, and avoid breathing fumes. Be especially careful with galvanized, plated or painted metal, which can give off harmful fumes.
  • Keep flammable materials away from the work area and have a way to put out a fire.
  • Secure gas cylinders upright and keep them away from heat.
  • Follow your machine’s manual and local rules.

This is general information, not a substitute for proper training or the manufacturer’s instructions.

Next steps in this guide

Keep exploring

Guides from other topics

All topics →