What is metal-cored arc welding?
Metal-cored arc welding (MCAW) is a wire-fed arc welding process that uses a tubular wire with a core of metal powder instead of a solid wire. As with MIG welding, an external shielding gas protects the arc. The wire is fed continuously from a spool through a gun, and the equipment looks very similar to a MIG setup.
Because it uses gas shielding and a continuous wire, it is often treated as a variant of gas metal arc welding (GMAW). However, the tubular construction is something it shares with flux-cored wire, which is why the two are often confused.
How MCAW works
The outer sheath of the wire is metal, usually steel for common carbon-steel wires. Inside is a powder that mainly contains metal alloying and deoxidizing elements, with only small amounts of non-metallic compounds. When the arc melts the wire, the sheath and the core melt together and transfer into the weld pool, while shielding gas keeps the air out.
Typical details, which vary by wire and manufacturer:
- The power source is usually a constant-voltage machine, the same type used for MIG.
- Shielding gas is generally an argon/CO2 mixture; the wire manufacturer’s datasheet gives the recommended gas.
- Metal-cored wires are often used in spray-type transfer at higher settings, but many can also be used at lower currents.
- Because the core has little flux, only a very thin, easily removed slag is left, if any.
MCAW vs solid wire MIG vs flux-cored wire
| Solid-wire MIG | Metal-cored (MCAW) | Flux-cored (FCAW) | |
|---|---|---|---|
| Wire construction | Solid | Tubular, metal powder core | Tubular, flux core |
| Shielding | External gas | External gas | Self-shielded or external gas |
| Slag | None | Very little | Yes, needs chipping |
| Spatter | Varies with settings | Often lower | Varies |
| Deposition rate | Moderate | Often higher | Often higher |
| Cost of wire | Lowest | Higher | In between |
| Outdoor use | Poor (gas blows away) | Poor (gas blows away) | Self-shielded wire works better |
“Often” is deliberate: the details depend on wire, gas and settings.
Advantages
- Higher deposition rates than solid wire in many applications, which can mean faster welding on thicker material.
- Good sidewall fusion, thanks to the wire’s arc characteristics, which helps reduce lack-of-fusion defects.
- Little slag and clean welds, so less post-weld cleanup than flux-cored wire, and multi-pass welds can go together faster.
- Lower spatter in many cases.
- Good tolerance of mill scale compared with some solid wires, according to manufacturers, although clean metal is still best.
Limitations and disadvantages
- Wire cost per pound is generally higher than solid wire.
- Shielding gas is required, so it has the same wind sensitivity as gas-shielded MIG. Drafts disturb the arc and can cause porosity; see porosity in MIG welds.
- Wire feeding can be fussier. Tubular wire can be crushed by too much drive roll pressure, and many suppliers recommend knurled or suitable drive rolls.
- Storage matters. Powder cores can absorb moisture if the wire is stored poorly.
- Less common for small shops. Small spools may be hard to find, and not every light-duty MIG machine is suited to it.
Typical applications
MCAW is common where speed and productivity matter, including:
- Structural steel fabrication
- Heavy equipment and machinery
- Trailers and transport equipment
- Pressure vessels and other applications where the code and welding procedure allow it
- Robotic and mechanized welding
Equipment and shielding gas
You need a MIG-style constant-voltage welder, a gas supply, a regulator and flowmeter, and a gun that can handle the wire size. Check that the feeder handles tubular wire, use the drive rolls the wire maker recommends, and follow the datasheet for polarity, gas and wire feed speed. General setting principles from our wire feed speed and MIG shielding gas articles carry over, but always defer to the manufacturer’s data for the specific wire.
Is MCAW worth it for a home shop?
For most hobbyists, standard solid-wire MIG is cheaper, easier to find and good enough. MCAW starts to make sense when you weld thick steel regularly, want higher deposition rates and have a machine and feeder suited to it. If you are still learning the basics, start with the MIG and TIG overview and good MIG settings.
Quick answers
Which welding process uses a flux core wire? Flux-cored arc welding (FCAW). Metal-cored wire is related but is intended to be used with shielding gas and leaves little slag.
What are the disadvantages of GMAW? Gas-shielded wire welding is sensitive to wind, needs a gas supply, is less portable than stick welding and requires fairly clean metal. Short-circuit transfer can also be prone to lack of fusion on thicker sections if settings are too cold.
What is MMA and TIG? MMA (manual metal arc) is another name for stick welding (SMAW). TIG is tungsten inert gas welding (GTAW).
What are the four types of arc welding? Commonly listed as stick (SMAW), MIG (GMAW), flux-cored (FCAW) and TIG (GTAW). Metal-cored welding is usually grouped with GMAW. Submerged arc welding is another arc process, mostly used in industrial settings.