The short answer: a basic soldering kit
Soldering joins two metal parts by melting a lower-melting filler metal (solder) into the joint. For how this differs from brazing and welding, see torch brazing and bronze welding. You need a heat source, solder, flux, a way to hold the work, and basic safety gear. Which version of each depends on the job. A circuit-board repair, a copper pipe, and a silver ring all use soldering, but they use quite different equipment.
A minimal electronics kit usually looks like this:
- A soldering iron or station with a suitable tip
- Rosin-core solder
- Tip cleaner (brass wool or a damp sponge) and tip tinner
- Desoldering braid or a solder pump
- Flush cutters and tweezers
- A heat-resistant mat, holding aids, and safety glasses
Plumbing and jewelry work swap the iron for a torch and use different solder and flux. Those differences are covered below.
Heat sources
Soldering irons. A basic pencil iron is fine for occasional wiring jobs. Beginners often do better with an adjustable-temperature iron, because a fixed-heat iron can overheat delicate parts or struggle on larger ones. Wattage matters less than how well the iron recovers heat when it touches the work, but very low-wattage irons tend to struggle with larger joints.
Soldering stations. A station pairs the iron with a base unit that controls temperature. It costs more than a basic iron, but it holds a set temperature better and usually accepts a wide range of replaceable tips. If you plan to solder regularly, a station is usually the better long-term purchase.
Cordless and portable irons. Battery or USB-powered irons are handy for quick repairs away from a bench. They are generally less suited to heavy, all-day work.
Soldering guns. Pistol-grip guns heat fast and suit heavier wiring and larger joints. They are less precise, so they are not a good choice for circuit boards.
Torches. Plumbing and jewelry work need more heat than an iron delivers, because the parts are bigger and conduct heat away quickly. Plumbers typically use a propane or MAPP-type gas torch; jewelers use a small propane, butane, or similar torch. See our guides to soldering copper pipe joints and silver soldering for jewelry.
Solder: alloys and forms
Solder is the filler metal. The main distinction is between leaded and lead-free alloys.
- Tin-lead solder (for example 60/40 or 63/37 tin/lead) melts at a lower temperature and flows easily, which many beginners find forgiving. It contains lead, so it needs careful handling and is not suitable for drinking-water plumbing or food-contact items.
- Lead-free solder is typically tin combined with copper, silver, or other metals. It melts at a higher temperature and can be a little harder to work with, but it avoids lead.
Our article on leaded vs lead-free solder goes into the trade-offs and the safety side.
Electronics solder commonly comes as thin wire with a flux core. Plumbing solder is usually a thicker wire without a flux core, used with separate paste flux. Jewelers use small pieces or sheets of silver solder, which melts at much higher temperatures than tin-based solders. If you are wondering what metal soldering uses, the answer is: it depends on the alloy, but tin is the main ingredient in most common solders, and silver solders add silver, copper, and zinc.
Flux: what it does and which type to use
Metal surfaces oxidize, and molten solder will not bond properly to an oxidized surface. Flux removes light oxidation and keeps the metal from re-oxidizing while it is heated. Without it, solder tends to ball up instead of flowing.
- Rosin flux is common in electronics and is often built into the solder core.
- Water-soluble or no-clean flux is used in electronics manufacturing and some hobby work. Follow the manufacturer’s instructions about cleaning.
- Plumbing paste flux is used on copper pipe and fittings. Some fluxes are acidic, so check the label for the intended use.
- Borax-based flux is typical for silver soldering.
Use the flux designed for your job. In particular, acid-type plumbing flux should not be used on electronics, because residue can corrode components over time.
Supporting tools
- Tip care: brass wool or a slightly damp sponge for cleaning the tip, plus tip tinner to refresh a dirty one. A clean, tinned tip transfers heat far better.
- Desoldering: braid (wick) and a solder pump are the basic ways to remove solder. They are also the main tools for fixing errors; see how to fix a soldering mistake.
- Holding: helping hands, a PCB holder, clamps, or a vise keep the work still while it cools. Movement during cooling is a common cause of weak joints.
- Cutting and handling: flush cutters for trimming leads, wire strippers, and fine tweezers.
- Cleaning: isopropyl alcohol and a brush for removing flux residue from electronics. For metalwork and pipe, emery cloth or a wire brush to get bare, bright metal.
Safety gear and workspace
- Eye protection. Solder and flux can spit, and clipped wire ends can fly.
- Ventilation or fume extraction. Flux fumes are irritating, and you should avoid breathing them. A small fan blowing across the work, away from you, helps, but a proper fume extractor is better.
- A heat-resistant work surface. Silicone mats are common. Keep flammable materials away, and keep the iron in a proper stand.
- Hand washing. If you use leaded solder, wash your hands after handling it and before eating, and do not eat or drink at the bench.
- For torch work: a fire extinguisher nearby, a heat shield, and gloves suited to the task.
Matching the kit to the job
- Electronics: temperature-controlled iron, thin rosin-core solder, braid or pump, flush cutters.
- Copper plumbing: torch, lead-free plumbing solder, paste flux, tubing cutter, deburring tool, emery cloth, and fitting brush.
- Jewelry and silversmithing: torch, soldering block, silver solder, flux, pickle, and tweezers. Details in our silver soldering guide.
- Pewter: low-heat tools and a low-melting solder, since pewter melts easily. See how to solder and repair pewter.
- Stained glass: an iron with a larger tip, plus the right solder and flux for the craft.
Not every metal accepts solder. If a joint refuses to take, see what metals solder will not stick to.
The 7 basic steps of soldering
Sources divide the process differently, but a seven-step version looks like this:
- Prepare the workspace. Ventilation, mat, safety glasses, tools within reach.
- Heat and tin the tip. Let the iron reach temperature and coat the tip with a little solder.
- Clean the parts. Remove dirt, oxide, and grease.
- Secure the parts. Hold them still and in contact.
- Heat the joint. Touch the tip so it heats both parts.
- Apply solder. Feed it to the heated joint, not to the iron tip, and let it flow.
- Remove the heat, let it cool undisturbed, then inspect. The joint should be smooth and shiny (with leaded solder) rather than lumpy.
Some guides use four or five steps; they are the same process grouped differently.
The golden rule of soldering
The most commonly cited rule is to heat the parts, not the solder. The workpiece should be hot enough to melt the solder on contact, which pulls it into the joint. If you melt solder on the iron and drop it onto cold metal, you tend to get a weak, dull “cold” joint.
Where to buy
Electronics suppliers, hardware stores, and plumbing suppliers are the most reliable sources, with jewelry-supply shops for silver solder. Some craft stores, including Hobby Lobby, may stock basic soldering supplies, but availability varies by location, so check with your local store before making a trip. Starter kits can be convenient, but the included iron is often basic, so check that the temperature can be controlled.
Where to go from here
Start with the job you actually want to do, buy the matching kit, and practice on scrap before working on anything valuable. If a joint goes wrong, our guide on fixing a soldering mistake walks through the common problems.