Before you start
Soldering copper pipe (often called “sweating” a joint) joins a copper tube to a fitting with solder drawn into the gap by capillary action, the same principle behind torch brazing. Done well, the joint is strong and watertight. Done badly, it can leak, sometimes only after the wall has been closed up.
A few points before you begin:
- Use lead-free solder for drinking-water lines. In the US and many other countries, lead solder is not permitted for potable water. See leaded vs lead-free solder for the background.
- Check local codes. Some places require a licensed plumber or a permit for certain work. Check before starting.
- This is torch work. Fire is the main hazard. Read the safety section below before lighting anything.
- Soldering is for water lines, not gas lines. Do not use this method on gas piping.
- If you are unsure, hire a plumber. Hidden leaks and fire risks are not worth gambling on.
Tools and materials
- Propane or MAPP-type gas torch, with striker or igniter
- Lead-free plumbing solder (wire) suitable for potable water
- Plumbing paste flux (labeled for use with lead-free solder)
- Tubing cutter (a hacksaw works if you cut square and deburr well)
- Deburring tool or reamer
- Emery cloth or sand cloth, and a fitting brush
- Acid brush (or similar small brush) for flux
- Clean rags
- Heat shield or fire-resistant cloth
- Safety glasses, and heat-resistant gloves if you like
- Fire extinguisher or a bucket of water within reach
For more on the equipment choices, see soldering tools and materials.
Step 1: Shut off the water and drain the line
Turn off the water supply and open a tap to drain the line as completely as you can. Water left in the pipe prevents the joint from reaching soldering temperature and is a common cause of failed joints, because the water carries heat away and may push steam through the joint. The pipe should be dry at the joint.
Also check what is behind and around the joint. Wood framing, insulation, paper, and wiring can all catch fire or melt.
Step 2: Cut and deburr
- Measure carefully, then cut the pipe square with a tubing cutter. A crooked cut leaves a gap in the fitting that solder may not fill.
- Remove the burr from the inside and outside edge of the cut. A deburring tool or reamer does this quickly. Burrs can restrict flow and leave a gap.
Step 3: Clean the surfaces
Solder will not flow over dirty or oxidized copper.
- Scrub the outside of the pipe end with emery cloth until it looks bright and shiny, to a bit beyond the depth of the fitting.
- Clean the inside of the fitting with a fitting brush or emery cloth.
- Wipe off any dust with a clean rag.
- Avoid touching the cleaned surfaces with your fingers, because skin oils can interfere with soldering.
Step 4: Apply flux and assemble
Using the brush, spread a thin, even layer of flux on the cleaned end of the pipe and inside the fitting. Push the pipe fully into the fitting, and give it a slight twist to spread the flux. Wipe off any excess.
Do not use too much flux. A thin layer is enough, and excess can leave residue inside the line. Support the joint so it does not move while heating and cooling.
Step 5: Heat the joint
- Place a heat shield behind the joint if nearby surfaces could be affected.
- Light the torch and adjust the flame according to the manufacturer’s instructions.
- Heat the fitting, concentrating on the thickest part, and move the flame so heat spreads around the joint. Keep the flame moving rather than sitting in one spot.
- Watch the flux. Heating until it bubbles or sizzles is often a sign that the joint is close to ready, but the real test is whether solder melts when touched to the joint.
Do not overheat. If the flux turns black or burns, the joint is too hot or has been heated too long, and the solder may not flow properly. Let it cool, clean it, and start over.
Step 6: Apply the solder
Touch the end of the solder wire to the joint at the seam, on the side opposite the flame. If the copper is hot enough, the solder will melt on contact and capillary action will draw it into the joint. Do not melt the solder with the flame directly.
Feed solder around the seam until a thin, even ring shows all the way around. For a typical small-diameter pipe, you do not need a lot of solder; follow the solder manufacturer’s guidance on how much to use. If solder keeps running out of the joint instead of filling it, the joint is probably too hot or there is water inside.
For vertical joints, work with gravity in mind, and take care with solder dripping onto things below.
Step 7: Cool and clean
Take the flame away once the ring of solder has formed. Let the joint cool naturally without moving it. Moving it or quenching it with water too quickly can crack the joint. Once it is cool enough to touch safely, wipe off excess flux with a damp rag, because leftover flux can corrode the pipe over time.
Test the joint
When all joints are finished, turn the water back on slowly, check each joint for drips, and check again after some time. A small weep may mean the joint needs to be redone. To fix a leaking joint, drain the line completely and see how to fix a soldering mistake. In short, do not just add more solder to a leaking joint; reheat, separate, clean, and redo it.
Common problems
- Solder will not flow into the joint. Usually the copper is dirty, the joint is not hot enough, or water is in the line.
- Solder balls up or runs off. The joint was not cleaned or fluxed properly, or the surfaces were not evenly heated.
- Burned flux. Overheating. Start again with fresh flux.
- Gap or uneven fill. Often due to a poor cut or an incompletely seated pipe.
- Leak after a day or so. The joint may have had an incomplete fill that is not visible from the outside. Cut out the joint and redo it.
- Damage to nearby parts. Valves with rubber or plastic parts can be damaged by heat. Check the manufacturer’s instructions, since some valves need to be disassembled or opened first.
If the solder refuses to bond, remember that copper itself is among the easiest metals to solder, so it is nearly always a cleaning, flux, heat, or moisture issue. Other metals are covered in what metals solder will not stick to.
Safety
- Fire is the main risk. Use a heat shield, keep a fire extinguisher or water nearby, and watch for smoldering after you finish. Check behind walls and framing.
- Wear safety glasses. Hot flux and solder can spit.
- Ventilate the area. Flux fumes are irritating.
- Hot metal stays hot. Allow the joint to cool before touching it.
- Check the torch and cylinder for leaks and damage, and handle fuel cylinders according to the manufacturer’s directions.