Shop Setup and Safety

Storing and Securing Welding Gas Cylinders Safely

How to store gas cylinders in a welding shop: secure them upright, keep valve caps on, separate oxygen from fuel gases, ventilate and check for leaks.

On this page
  1. Why cylinder storage matters
  2. Secure cylinders upright
  3. Valve protection and moving cylinders
  4. Where to store
  5. Keep oxygen and fuel gases apart
  6. Shielding gases and enclosed spaces
  7. Cylinders in use at the welder
  8. Leaks and damage
  9. Rules and your supplier

This article is general information. Rules for storing compressed gas differ by country, region and workplace, and your gas supplier and local fire authority are the right place to confirm requirements.

Why cylinder storage matters

Welding gas cylinders hold gas at high pressure. A cylinder that falls and breaks its valve can release gas suddenly and may become dangerous, and some gases are flammable or support combustion. Good storage habits mostly come down to keeping cylinders upright, secured, protected from damage and away from heat and ignition sources.

Secure cylinders upright

  • Keep cylinders upright and fastened to a wall, post, rack or cart with a chain or strap. A chain or strap about two-thirds of the way up the cylinder is a common recommendation.
  • Secure cylinders when they are full, empty, in storage and in use. Do not rely on leaning them in a corner.
  • Use a purpose-made cylinder cart for moving them, and strap them to the cart.
  • Do not lay cylinders flat for storage unless the supplier says it is acceptable for that gas, because some gases, such as acetylene, need to be kept upright.

Valve protection and moving cylinders

  • Keep the protective cap on whenever the regulator is not attached, including during transport and storage.
  • Close the cylinder valve when you are not welding, and when you move or store the cylinder.
  • Do not lift or move a cylinder by the valve or cap, and do not drag or roll it along the ground.
  • Do not drop cylinders or let them knock against each other.
  • Never alter or force a valve or fitting. If one is stuck or damaged, contact the supplier.

Where to store

Choose a place that is:

  • Well ventilated, so any small leak does not build up
  • Cool and dry, away from direct sunlight, radiators, furnaces and other heat. Many suppliers specify a maximum storage temperature, so check yours
  • Protected from vehicles, falling objects and being knocked
  • Away from sparks and grinding, from open flame, and from electrical equipment that could arc
  • Clear of exits and walkways
  • Off the ground in damp locations, since constant moisture can corrode the cylinder
  • Locked or restricted if other people use the building

Keep oxygen and fuel gases apart

Oxygen makes fires burn much more fiercely. Cylinders of oxygen should be stored separately from fuel gases such as acetylene or propane. Regulations commonly require either a minimum distance or a fire-resistant barrier between them, with distances such as 20 feet (about 6 m) often cited in the US, but the requirement depends on where you live, so confirm it. Keep oil and grease away from oxygen valves, regulators and fittings, and do not handle them with greasy gloves.

Shielding gases and enclosed spaces

Argon, carbon dioxide and argon mixes used for MIG and TIG welding are not flammable, but they can displace oxygen in the air. In a small or poorly ventilated room a significant leak can create a breathing hazard. Store them in a ventilated area rather than a closed cupboard, and avoid taking cylinders into confined spaces. See welding shop ventilation and fume extraction basics.

Cylinders in use at the welder

  • Secure the cylinder on the welder’s cart or to a wall nearby, with the valve accessible
  • Crack the valve briefly to clear dirt before attaching the regulator, standing to the side and away from other people, and away from ignition sources
  • Use a regulator designed for the specific gas, and do not interchange them
  • Open the valve slowly, and close it when you finish
  • Keep cables and torch leads from touching the cylinder, because an arc striking a cylinder can weaken it. Never strike an arc on a cylinder

Leaks and damage

Check connections for leaks with soapy water or a leak-detection solution, not a flame. If you smell gas, hear hissing, or see a damaged cylinder or valve, stop work, shut the valve if it is safe to do so, ventilate the area, keep ignition sources away and call your supplier or the emergency services as appropriate. Do not use cylinders that are dented, corroded or have a damaged valve, and return them to the supplier.

Rules and your supplier

Your gas supplier can explain the cylinder type, test dates, rental terms and storage guidance for your region. If you run a business or have employees, workplace rules may also apply. For the wider plan, see setting up a welding shop, and for protective gear, what safety equipment is needed for welding.

The complete guide to shop setup and safety

Setting Up a Welding Shop: Equipment and Machine Parts
Read the guide

Keep exploring

Guides from other topics

All topics →