What arc welding is in one paragraph
Arc welding joins metal by using an electric arc as the heat source. The arc is struck between an electrode and the workpiece, and it melts the edges of the joint (and usually the electrode or filler too). The molten metal forms a pool that cools and solidifies into a single joined piece. Everything else in arc welding, from the machine to the rod to the technique, exists to start that arc, keep it stable and protect the molten metal while it freezes.
What the arc actually is
An electric arc is a sustained electrical discharge through a gap. When the electrode is touched to the work and then lifted a short distance, current keeps flowing across the gap through ionised gas, which is called plasma. The arc is extremely hot, far above the melting point of steel (which is roughly 1,400 to 1,500 °C, depending on the alloy), and it is also intensely bright and rich in ultraviolet light, which is why eye and skin protection matter.
Welders usually describe the gap in terms of arc length. A short, steady arc gives a stable, focused heat input. A long arc wanders, spatters and lets air in. Much of learning to weld is learning to hold a consistent arc length, which is covered in arc welding lessons.
The circuit: how an arc welder is designed
A welding machine is, at heart, a power source that turns mains or generator power into a low-voltage, high-current output. The circuit runs from the machine through the electrode lead to the electrode holder, across the arc, into the workpiece, and back to the machine through the work lead and clamp. Because the arc is part of the circuit, the placement of the work clamp matters; see where to put the ground when welding.
Constant-current output
Stick welding machines are normally designed with a constant-current (also called drooping) output. In practice this means that as the arc length changes slightly, the current stays close to the set value while the voltage changes. That is what makes manual welding workable: your hand will never hold the arc length perfectly, and the machine keeps the amperage reasonably steady anyway. Typical arc voltage while welding is in the region of 20 to 30 volts, while the open-circuit voltage (before the arc is struck) is higher, which helps the arc start.
Transformer, rectifier and inverter machines
Common machine designs include:
- Transformer (AC) machines. The simplest design. A heavy transformer steps mains voltage down to a high-current AC output. They are rugged and inexpensive but heavy, and they only provide AC.
- Transformer-rectifier machines. Add a rectifier so the output can be DC, often with selectable polarity and sometimes AC as well.
- Inverter machines. Convert the incoming power to high frequency, step it down with a much smaller transformer, then rectify it. They are light, portable and efficient, and usually offer smoother arc control features. Most modern hobby stick welders are inverters.
For what AC and DC mean for your arc and your electrode choice, see what is AC and DC arc welding.
Engine-driven welders
Engine-driven welder-generators combine a generator with a welding power source. They are common on remote job sites and farms because they do not need mains power (see basic welding for farm and ranch).
How the flux coating shields the weld (the “enclosed” arc)
Molten steel readily absorbs oxygen and nitrogen from air, which leads to porosity and brittle welds. Every arc welding process therefore has some way of shielding the molten pool. In stick welding the shielding comes from the electrode coating, called flux. As the rod burns, the coating does several jobs:
- It releases gases that push air away from the arc and pool.
- It forms a layer of molten slag that floats on the weld and slows cooling.
- It carries arc-stabilising and alloying ingredients.
People who search for terms such as “enclosed arc welding” are usually describing this idea: the arc is surrounded by its own protective atmosphere created by the flux, rather than being open to the air. (Submerged arc welding is a separate industrial process in which the arc is literally buried under a blanket of granular flux.) For more on how coatings differ, see stick welding rods explained.
MMA, MMAW, SMAW and stick: what the names mean
These all describe essentially the same process:
- MMA or MMAW: manual metal arc (welding). Common in the UK, Australia and much of Europe.
- SMAW: shielded metal arc welding. The formal American Welding Society term.
- Stick welding: the everyday name, because the electrode is a stick (rod) held in a holder.
The electrode is consumed as you weld, and the welder feeds it into the joint by hand, hence “manual”.
Does MMA welding need gas?
No. Standard MMA/stick welding does not use a gas bottle, because the flux coating generates its own shielding gas as it burns. That is a large part of why stick welding is popular for outdoor work and in breezy conditions, where the gas shield used in MIG or TIG could be blown away.
The main arc welding processes compared
When people ask “what are the four types of arc welding”, they usually mean the four most common processes:
- Stick (SMAW/MMA): a flux-coated rod, no gas bottle, very portable, tolerant of dirty or outdoor conditions. Slag has to be chipped off.
- MIG (GMAW): a continuously fed wire electrode with shielding gas from a bottle. Fast and easy to learn, best in sheltered conditions.
- Flux-cored (FCAW): a tubular wire containing flux. Can be run with or without external shielding gas depending on the wire, and produces slag.
- TIG (GTAW): a non-consumable tungsten electrode with shielding gas, and filler rod added by hand. Gives very controlled, clean welds but takes more skill and prep. For a side-by-side comparison, see the difference between TIG and MIG.
Submerged arc welding (SAW) is also widely used in industrial fabrication. Note that MIG welding is itself a type of arc welding, so “MIG versus arc welding” is really MIG versus stick in most casual usage.
If you are choosing where to start, stick welding is a very cheap and forgiving way to learn arc fundamentals such as arc length, travel speed and puddle reading.
Resistance and laser welding are not arc welding
Related questions often mention RSW and LBW. RSW is resistance spot welding, where sheets are squeezed between electrodes and joined by the heat from current passing through them. LBW is laser beam welding, which uses a focused laser. Neither uses a welding arc, so they fall outside this cluster.
The five basic joint types
Welds are made on a handful of joint configurations, covered in more depth in the 5 basic weld types. The five usually listed are:
- Butt joint
- T-joint
- Lap joint
- Corner joint
- Edge joint
On top of the joint type, the weld itself might be a groove weld or a fillet weld, and it might be made in flat, horizontal, vertical or overhead positions; welding positions and techniques covers each one.
Safety basics
Arc welding involves hazards that are easy to underestimate, so follow your machine manual and local rules, and consider formal instruction if you are new. In general:
- Use a welding helmet with the correct filter shade, plus flame-resistant clothing, gloves and closed footwear.
- Keep flammable materials well away from the work area.
- Make sure fumes are ventilated or extracted, especially when welding coated or galvanised metal. See welding shop ventilation and fume extraction basics.
- Never weld on containers that have held flammable substances unless they have been properly prepared by someone qualified.
- Do not touch live parts of the electrode circuit, and keep gloves and clothing dry.
Where to go next
- Practise the physical skills in arc welding lessons: striking and holding an arc.
- Learn the basic rod types in stick welding rods explained.
- Work on bead technique in how to lay a weld bead.
- Set your machine with the stick welding amperage chart.