What a first arc welding lesson looks like
A first stick welding session is not about making pretty welds. The goals are to get comfortable under the helmet, strike an arc reliably, and hold a steady arc length while moving along a plate. Expect to burn through a fair number of rods doing only that. If you want background on the process before you start, read how arc welding works.
Before you strike an arc
Set up so that the only new thing you are learning is the arc:
- Practice plates. Clean mild steel, a few millimetres to a quarter inch thick, with mill scale, rust and paint ground off where you will weld.
- Work clamp. Attach it firmly to bare metal on the plate or table. A poor connection is a common cause of erratic arcs; see where to put the ground when welding.
- Electrode. A general-purpose, easy-running rod such as 6013 is a common choice for first practice. Rod types are covered in stick welding rods explained.
- Amperage. Start in the middle of the range printed on the rod packaging, and adjust from there. The stick welding amperage chart gives typical starting points.
- Protection. Helmet with the right filter shade, flame-resistant clothing, dry gloves, closed footwear, and ventilation (see what safety equipment is needed for welding). Keep flammable items well clear.
Ideally, have an instructor or experienced welder check your setup the first time.
Two ways to strike an arc
There are two standard starts:
- Scratch start. Drag the tip of the rod across the plate like striking a match, then lift slightly the moment the arc forms. It tends to feel natural to beginners but can leave stray arc marks on the work if you scratch outside the joint.
- Tap start. Bring the rod straight down, tap it briefly on the plate and lift it back up a few millimetres to establish the arc. It is more controlled about where the arc begins, but it takes timing and can make the rod stick if you hold the contact too long.
In both cases, the key is the lift. If the rod stays in contact, it will freeze to the plate. If you pull too far, the arc goes out. If your rod keeps freezing, see why your stick electrode keeps sticking.
What “tapping” means in welding
The search term “tapping in welding” can refer to several different things:
- Tap start, as above, which is the meaning most relevant to learning arc welding.
- Hot tapping, a specialised pipeline technique for connecting a branch to a live pipe, done under strict procedures by qualified crews. It is not a beginner topic.
- Tapping threads into a drilled or welded hole, which is a machining operation.
Holding the arc: length, angle and travel speed
Once the arc is lit, three things determine how the weld looks:
- Arc length. A common rule of thumb is to keep the gap roughly equal to the diameter of the rod’s metal core, though this varies with the electrode type. Too long and the arc becomes noisy and spattery; too short and the rod sticks.
- Angle. Tilt the rod so it leans in the direction of travel by a modest angle (commonly cited as around 10 to 15 degrees from vertical, up to 30 for some situations) while keeping it square to the joint from the side. For more detail see do you push or pull when arc welding.
- Travel speed. Move at a pace that keeps the puddle a consistent width. The puddle and slag trailing behind will tell you whether you are too fast or too slow.
Because the rod burns shorter, you have to feed it toward the work as you go. That constant feeding is the hardest coordination to learn.
A simple practice plan
- Strike and hold. Practise starting arcs and holding them in one spot for a second or two, then stopping. Repeat until starts are consistent.
- Straight lines. Run single beads across a flat plate, one line after another. Chip the slag off and inspect each one.
- Weave beads. Practise a small side-to-side motion to widen the bead. Stringer beads vs weaving covers when each is used.
- Fillet welds. Make T-joint welds with two plates.
- Other positions. Only move to vertical and overhead once flat welds are consistent; welding positions and techniques explains each position.
The details of bead shape and quality are in how to lay a weld bead.
Tack welds
A tack weld is a small, temporary weld used to hold parts in position before the final welding. Tacks keep the joint aligned and the gap consistent as heat causes the metal to move. They should be made with the same care as the finished weld since they are normally fused into it.
What to learn first
Many beginners start with stick or MIG. Stick is inexpensive, works outdoors and teaches fundamentals about arc length and puddle control. MIG is generally considered easier to pick up for thin, clean steel (see how MIG and TIG welding work). Choose based on the projects you want to do and your budget; neither choice locks you in.
Common beginner problems
- Rod sticking: often amperage too low, or slow lifting after contact.
- Arc going out: pulling the rod away too far at the start or while welding.
- Spatter and a rough bead: arc too long, amperage too high, or damp rods.
- Poor penetration or a bead that sits on top: moving too fast or amperage too low.
None of these are unusual in the first hours. Short, frequent practice sessions with plenty of inspection usually beat long, tiring ones.