The short answer
Use stringer beads when you want low heat, narrow beads and good control, such as on root passes, thin or heat-sensitive material, overhead work, and when a procedure requires it. Use a weave when you need to fill a wider joint or gap in fewer passes, as long as heat input and the welding procedure allow it. Neither technique is better in all cases. Many welds use both, for example a stringer root pass followed by weave fill and cap passes.
What is a stringer bead?
A stringer bead is made by moving the electrode or gun in a straight line along the joint with little or no side-to-side motion. The bead width is determined mainly by the electrode size and travel speed, so it is relatively narrow. Welders may still make small movements, such as a slight circular motion or a “whip,” to manage the puddle, but the overall travel is straight.
What is a weave bead?
A weave bead is made by moving the electrode or gun from side to side as you travel along the joint, so the finished bead is wider than a stringer. The motion spreads heat across a wider area and builds up more filler metal per pass. It is common for filling wide grooves, large fillets, and for cap passes where a wider, flat bead is wanted.
Stringer vs weave: comparison
| Stringer bead | Weave bead | |
|---|---|---|
| Bead width | Narrow | Wider |
| Heat input | Generally lower, more concentrated | Generally higher, spread over a wider area |
| Distortion | Often less on thin or long welds | More likely if overdone |
| Passes needed to fill a joint | More | Fewer |
| Control of puddle | Easier, especially out of position | Harder, needs practice |
| Risk of slag traps | Lower if cleaned between passes | Higher at the edges if you move too quickly |
| Typical use | Root passes, thin metal, overhead, tough procedures | Fill and cap passes, wider joints, flat and some vertical work |
These are general tendencies, and results depend on settings, process, and the welder.
When to use stringers
- Root passes, where you want controlled penetration and fusion at the root of a groove.
- Thin or heat-sensitive metal, to limit distortion and burn-through.
- Overhead welding, where a small puddle that freezes quickly is easier to control. See overhead welding: technique, settings and safety tips.
- Procedures that call for them. Some procedures, such as those for certain high-strength, low-temperature or impact-tested work, specify stringer beads or limit heat input.
- Learning. Stringers teach arc length, angle and travel speed without the extra variable of side-to-side motion.
- Multi-pass fillets, where each small pass is easier to inspect and clean.
When to use a weave
- Wide grooves and gaps, where a single stringer would not reach both sides.
- Cap passes, where a wider and flatter appearance is desired.
- Vertical up welding, where a small weave or triangular motion with pauses at the sides helps the puddle tie in and build; see vertical up welding.
- Larger single-pass fillets in the flat or horizontal position, within the limits for your electrode and joint.
- Productivity, when the material and procedure allow more heat input and you want fewer passes.
Weaving is not a way to make a weld bigger than the settings can support. If the puddle gets too large, it will sag, undercut or trap slag, and the weld may not fuse properly.
Common weave patterns
- Zigzag or side-to-side: simplest, with a brief pause at each edge.
- Crescent or “C”: a curved motion that helps fill the sides.
- Circular: small loops, often used to control a fluid puddle.
- Triangle or “Christmas tree”: used on vertical-up welds, where you widen as you go up.
- J-pattern: often used on TIG or MIG to add filler in a controlled way.
A usual guideline in stick welding is to keep the weave width to a few times the electrode diameter, rather than a wide sweep, but the specific limit depends on the electrode and procedure.
Process notes
- Stick (SMAW): low-hydrogen rods are often run as stringers or with limited weave, while some other rod types are more comfortable to weave. Follow the guidance of the electrode manufacturer.
- MIG and flux-cored: both techniques are used, and flux-cored often needs careful slag control, particularly out of position.
- TIG: the bead is mostly a stringer with a slight side-to-side motion or a “walking the cup” movement. Heat is added and removed with filler additions and pedal control. See what are common TIG welding mistakes.
Procedures and codes
In code or structural work, you generally follow a written welding procedure specification, which may limit weave width, heat input or interpass temperature, or prescribe stringer or weave for particular passes. Where there is such a procedure, it takes precedence over general guidance and personal preference. If you’re not sure, ask the inspector or supervisor before welding.
Practice tips
- Learn stringers first, then add a weave once you can keep consistent width, speed and arc length.
- Pause briefly at each side of a weave so the edges fuse, and don’t pause in the middle.
- Clean slag and check the toes between passes.
- Practice both in the flat position before moving to vertical and overhead.
- Cut or bend test pieces to look at fusion.
For how bead style fits with position, angle and travel speed, see welding positions and techniques for beginners, and for the variables behind a good bead in general, what are the 5 essentials in welding.