Positions and Techniques

Welding Inside Corners and Fillet Joints

Learn how to weld inside corners and fillet joints: joint types, torch and electrode angles, tight-access tricks, fillet size, and fixes for common defects.

On this page
  1. What is an inside corner weld?
  2. Joint types that make inside corners
  3. Prep and fit-up
  4. Gun or electrode angles
  5. Step-by-step: running a fillet in an inside corner
  6. Getting into tight corners
  7. Fillet size and bead shape
  8. Common defects and fixes
  9. Which position is hardest?

What is an inside corner weld?

An inside corner is where two pieces of metal meet at roughly a right angle, and you weld on the inside of the “V” they form. Welders usually call the resulting weld a fillet weld, which has a roughly triangular cross-section and joins the two surfaces. “Corner welding” is a general term, and it can mean welding either the inside or the outside of such a joint. Inside-corner fillets are among the most common welds in fabrication because they are simple to prepare and can be made in any position.

Joint types that make inside corners

  • T-joint: one piece stands on the face of another. You can weld both sides, giving two inside corners.
  • Corner joint (inside): two pieces meet at an angle, with the weld in the inside corner.
  • Lap joint: two overlapping pieces; the fillet is made at the edge of the top piece, where it meets the surface of the lower one.

All three rely on the same idea: the weld has to fuse into both pieces at the root and at each toe, so the joint holds the load.

Prep and fit-up

  • Clean mill scale, rust, oil and paint from the surfaces to be welded and a short distance beyond.
  • Fit the parts tightly. Large gaps lead to a sagging bead or the need for extra filler.
  • Tack weld the parts so they don’t move as they heat. Tacks should be small and sound, because you will weld over them.
  • Check the square with a try square before final welding. Welds pull the parts toward each other as they cool.
  • Use a ground clamp on clean metal near the weld.

Gun or electrode angles

Two angles matter on a fillet:

  • Work angle: the tilt across the joint. A common starting point on equal-thickness plates is about 45 degrees, splitting the angle between the two surfaces. Tilt a bit toward the thicker or heavier piece if the thickness differs, since it needs more heat to get fusion.
  • Travel angle: the tilt along the direction of travel, often around 10 to 15 degrees. Whether you push or drag depends on the process. Stick and flux-cored are normally dragged. MIG is commonly pushed on thinner stock and dragged for more penetration.

Work from there based on how the puddle looks. If it is climbing one plate, tilt more toward the other.

Step-by-step: running a fillet in an inside corner

  1. Set up the joint in the flat or horizontal position if you can. This is easiest.
  2. Do a dry run of the gun or electrode path so you have access along the whole length.
  3. Strike the arc at the root of the joint and wait for the puddle to wet both plates.
  4. Aim into the root, not at the top of one plate. The arc should favor the root and the puddle should flow onto both surfaces evenly.
  5. Move at a steady pace. Watch both toes: you want the puddle edges to meet each plate without a gap or a groove.
  6. Fill craters at the end by pausing briefly, or backing up slightly, before breaking the arc.
  7. For larger fillets, use multiple passes instead of one big pass. A single oversized pass is more likely to sag or fail to fuse.

For stick or flux-cored welds, chip and brush the slag before laying the next pass. For the technique difference between narrow beads and side-to-side motion, see stringer beads vs weaving.

Getting into tight corners

When the corner is hard to reach, for example inside a frame, box section or against a nearby wall:

  • Use a smaller or tapered nozzle, or temporarily remove the nozzle on MIG while keeping a safe gas coverage in mind. Without a nozzle, shielding gas coverage drops, so keep the stick-out short and check that gas coverage is still adequate.
  • Choose a longer or bent contact tip or a gooseneck designed for tight access.
  • Change position. Rotate the workpiece, if it is small enough, so that the joint is accessible and flat.
  • Consider self-shielded flux-cored wire where gas coverage is poor, though it produces more smoke and slag.
  • Use stitch welding (short welds with gaps) to reach tight areas in stages, if the design allows it.
  • On TIG, use a smaller cup or a gas lens to get the torch closer.

Always make sure you can see the puddle. If you can’t, it is better to rearrange the work than weld blind.

Fillet size and bead shape

Fillet size is measured by the length of the legs, the sides of the weld triangle along each plate. The required size comes from the drawing or code, not from how big the bead looks. A fillet gauge is an inexpensive way to check it. Aim for a slightly convex or flat face with smooth toes, and even legs unless the drawing calls for unequal ones.

For thicker joints that need more than one pass, vertical up welding and overhead welding both involve fillets made in more difficult positions.

Common defects and fixes

  • Undercut (a groove melted into the plate at the toe): the arc is too long, the heat too high, or the angle favors one plate. Shorten the arc and aim lower.
  • Lack of fusion at the root: the arc is not reaching the corner. Aim deeper into the root, slow down a little or increase heat.
  • Uneven legs: the angle is off or you are favoring one plate. Adjust your work angle toward the plate with the short leg.
  • Overlap (metal sitting on the plate without fusing): too slow, or too little heat. Increase speed or heat slightly.
  • Porosity: dirty metal or poor shielding. Clean the joint and check gas or electrode condition.
  • Burn-through on thin sheet: lower the heat, speed up, or use stitch welding.

Which position is hardest?

Fillets can be made in the flat (1F), horizontal (2F), vertical (3F) and overhead (4F) positions. Overhead is commonly considered the hardest, and flat the easiest. For a full explanation, see welding positions and techniques for beginners.

The complete guide to positions and techniques

Welding Positions and Techniques for Beginners
Read the guide

Keep exploring

Guides from other topics

All topics →