Stick Welding

Storing and Drying 7018 Rods: Rod Ovens and Low-Hydrogen Rules

Why 7018 low-hydrogen rods must stay dry, how sealed packs and rod ovens work, typical redrying guidance, exposure limits and storage options for a home shop.

On this page
  1. Why 7018 rods must be kept dry
  2. Sealed packaging and what to do after opening
  3. Rod ovens (holding ovens)
  4. Redrying (reconditioning) rods
  5. Exposure time limits
  6. Hobby and home workshop options
  7. Signs of damp rods
  8. Does it matter for non-critical work?

Why 7018 rods must be kept dry

E7018 is a low-hydrogen electrode. Its coating is formulated to leave very little hydrogen in the weld metal, which reduces the risk of hydrogen-induced cracking, a concern in higher-strength steels, thick sections and restrained joints. The catch is that this type of coating can absorb moisture from the air. Absorbed water becomes a source of hydrogen in the arc, which undermines the point of choosing the rod and can lead to porosity, spatter and cracking.

Other rods, such as 6010 and 6011, have coatings that are used with some moisture and are not treated in the same way. For the rod types in general, see stick welding rods explained.

Sealed packaging and what to do after opening

Low-hydrogen rods are usually sold in hermetically sealed metal cans or vacuum-type packs. While the container is intact and undamaged, the rods are considered protected, and many specifications permit them to be used straight from a freshly opened container. Once opened, the clock starts: rods exposed to humid air will pick up moisture over hours.

Common practice is to open only as many rods as you plan to use, and to transfer the rest to a heated holding oven or a sealed, dry container straight away. Do not leave an open box on the bench overnight.

Rod ovens (holding ovens)

A rod oven is a small heated cabinet that keeps electrodes warm and dry. Typical holding temperatures commonly quoted are around 250 to 300 °F (about 120 to 150 °C), although the exact figure should come from the electrode manufacturer’s data sheet or the code that applies to your work. Portable versions are used in fabrication shops and on job sites, so you can pull rods out a few at a time.

Note that a holding oven is for storing rods that are already dry. It is not the same as a drying (reconditioning) oven, which runs much hotter.

Redrying (reconditioning) rods

If low-hydrogen rods have been exposed for longer than the allowed time, some specifications permit redrying them in an oven at a much higher temperature, often quoted at around 700 to 800 °F (roughly 370 to 430 °C) for about an hour. Manufacturers differ on how many times rods can be redried, and repeated cycles can damage the coating. A typical kitchen oven does not reach these temperatures and is not an appropriate substitute. If a rod’s coating has cracked, flaked or been visibly wet, it is normally best to discard it.

Follow the manufacturer’s instructions where available. For work done under a code or procedure (structural, pressure or pipeline welding), the code’s requirements for exposure and redrying take priority over general advice. For how procedures are documented, see what WPS, WPQ and PQR mean.

Exposure time limits

Allowed exposure time varies by rod classification, manufacturer and code, and some moisture-resistant low-hydrogen rods (often marked with an “R” suffix) have longer limits. For standard E7018 in structural work, figures of a few hours are often quoted. Do not rely on a number from an article; check the data sheet and applicable specification.

Hobby and home workshop options

For non-critical home use, a few common approaches are:

  • Buy smaller containers so that you open a fresh can only when needed.
  • Use a sealed, airtight container with desiccant packs, and keep it in a dry place.
  • Buy a small rod oven or rod holding cabinet, which is a reasonable investment if you weld 7018 regularly.
  • Homemade holders made from sealed tubes or a heated enclosure are sometimes described online. If you build a heater, make sure it is electrically safe and does not overheat.

Store rods off a concrete floor and away from damp walls and temperature swings that cause condensation.

Signs of damp rods

  • Heavy spatter or a hissing or popping arc.
  • Porosity or pinholes in the weld.
  • Slag that is difficult to remove, or a rough bead.
  • Cracked or crumbling coating, or a visibly whitish bloom on the flux.
  • A rod that sticks or is hard to restart; see why your stick electrode keeps sticking.

Does it matter for non-critical work?

For a hobby project where failure is not dangerous, slightly damp 7018 will usually still weld, but the results are likely to be worse. For anything load-bearing or safety-related, treat moisture control seriously, and consider seeking qualified advice or formal procedures. When setting the machine, use the maker’s range or the stick welding amperage chart, and for background on how the process works, see how arc welding works.

The complete guide to stick welding

How Arc Welding Works: Stick, MMA and the Welding Arc
Read the guide

Keep exploring

Guides from other topics

All topics →