How to read a rod classification
Most mild-steel stick electrodes follow the American Welding Society naming system. Take E7018 as an example:
- E means electrode.
- 70 is the minimum tensile strength of the weld metal in thousands of pounds per square inch, so 70 means 70,000 psi.
- 1 (the third digit) is the welding position. A 1 means the rod is designed for all positions (flat, horizontal, vertical and overhead); a 2 means flat and horizontal only.
- 8 (the last digit, read together with the third) describes the coating type and the current the rod can use. For E7018, the coating is low-hydrogen with iron powder, and the rod runs on AC or DC with the rod positive.
The last two digits are best looked up in a chart rather than memorised as a formula. The same system applies to E6010, E6011, E6013 and others.
The common rods at a glance
- E6010: cellulose-based coating, deep digging arc, runs on DC with the rod positive only. Often used for root passes, pipe, and welding through some rust or dirt. For 6010 versus 7018 on pipe roots, see can you use 7018 for a root pass?
- E6011: similar in character to 6010 but formulated to run on AC as well as DC. A common choice for AC-only machines and general repair.
- E6013: a softer, smoother-running arc with a coating that is easy to strike and leaves a slag that usually peels readily. Runs on AC or DC. Penetration is moderate.
- E7018: a low-hydrogen rod producing strong, clean welds with a smooth arc, widely used for structural work and thicker steel. It needs careful storage; see storing and drying 7018 rods.
For currents, see what is AC and DC arc welding. For amperage ranges per size, see the stick welding amperage chart.
What 6013 is best used for
6013 is popular for light fabrication, sheet and thinner plate, and for beginners, thanks to its easy arc starts and gentle, forgiving behaviour. It is generally a good choice on clean metal where deep penetration is not required. It is less suited to critical structural or high-stress work, where rods like 7018 are commonly specified.
The amperage depends on the diameter and manufacturer. As a rough guide, many 1/8 inch 6013 rods are run somewhere around the low-to-mid 100-amp range, but check the packaging for the maker’s recommended range.
Overhead welding: which rod?
Overhead welding fights gravity, so you want a rod that freezes quickly and a small puddle. Technique is covered in overhead welding: technique, settings and safety tips.
6013 overhead
E6013 is classed as an all-position rod, and smaller diameters such as 3/32 or 1/8 inch are commonly used overhead. Keep the amperage toward the lower end of the rod’s range, hold a short arc and keep the puddle small. Too much heat makes the puddle sag and drip.
Can you overhead 7018?
Yes. E7018 is classified for all positions, and small-diameter rods are used overhead in structural work. It requires a short arc and tidy technique, and it is less forgiving than 6013. Whatever rod you choose, practise overhead only after you can weld consistently in the flat and vertical positions, and wear proper head and shoulder protection against falling spatter. Technique for travel direction is in do you push or pull when arc welding.
Rod sizes
Stick electrodes are sold by core wire diameter. Common sizes include 1/16, 5/64, 3/32, 1/8, 5/32, 3/16 and 1/4 inch, with metric equivalents of about 1.6, 2.0, 2.5, 3.2, 4.0, 5.0 and 6.0 mm, depending on the brand. Lengths vary, with 14 inches (about 350 mm) being typical for many sizes. In general, thinner metal calls for smaller rods and lower current, while thicker metal and higher currents call for larger rods.
How welding rods are made
In outline, commercial electrode manufacture involves:
- Core wire. Low-carbon steel wire is drawn to size, straightened and cut into lengths.
- Coating mix. Dry ingredients such as minerals, cellulose, iron powder, deoxidisers and arc stabilisers are blended with a liquid binder, commonly a silicate. The recipe determines the rod’s behaviour and classification.
- Extrusion. The mix is pressed into a paste and extruded onto the core wire in a uniform layer, with a bare end left for the holder and the striking end often shaped for easy starts.
- Baking. The rods are dried and baked in ovens. Low-hydrogen rods like 7018 are baked at higher temperatures so that very little moisture remains, which is why they are packed in sealed containers.
- Packing and testing. Rods are marked, inspected, sampled and packed.
Should you make your own rods?
Instructions for homemade rods circulate online, typically using steel wire and a homemade silicate coating. Treat them as curiosities. The recipes can involve caustic chemicals, the result is inconsistent, and a weld made with an unqualified rod may not be sound. Commercial rods are inexpensive and tested, so they are the practical option for anything that matters.
A note on welding threaded rod
Threaded rod can be welded, but the threads make heat control tricky and the material’s grade is often unknown, so results are unpredictable for load-bearing uses. Use a lower current, small rod and short tacks, and do not rely on such a weld where failure could injure someone.
Related reading
If your rod keeps freezing to the work, see why your stick electrode keeps sticking. For a general introduction, start with how arc welding works.