Soldering

What metals will solder not stick to?

Aluminum, stainless steel, titanium, magnesium, cast iron and chrome are hard to solder. Learn why solder won't stick and what to do instead.

On this page
  1. Short answer
  2. Why solder doesn’t stick to some metals
  3. Metals that are hard or impractical to solder
  4. Metals that solder easily
  5. When a normally solderable metal refuses
  6. What to do instead
  7. Safety note

Short answer

Standard solder does not stick well to aluminum, stainless steel, titanium, magnesium, cast iron, and chromium-plated surfaces. Strictly speaking, few metals are impossible to solder under any condition, but these are usually impractical with an ordinary iron and ordinary flux. For these, special preparation, a different filler, or a different joining method such as brazing or welding is normally needed.

Why solder doesn’t stick to some metals

Solder bonds by wetting. The molten solder has to spread across the metal and bond with its surface. That only works when the surface is clean, bare metal.

Most metals form an oxide layer in air. On copper, brass, and tin, the oxide is thin and easily removed by flux, so solder wets the surface easily. On other metals, the oxide is much tougher, forms again almost immediately, or the metal itself has properties that stop solder from bonding. Ordinary flux cannot remove it, so the solder beads up and rolls off.

Metals that are hard or impractical to solder

Aluminum. Aluminum forms a hard, thin oxide layer almost instantly. Specialized aluminum solders and fluxes exist, and some people have success with them, but results are often unreliable with ordinary tools. There is also a corrosion concern: joining aluminum to a different metal with solder can set up galvanic corrosion over time, especially if moisture is present.

Stainless steel. The chromium in stainless forms a durable oxide layer. Stainless steel can be soldered, but generally needs a more aggressive acid-type flux made for the purpose, thorough cleaning, and careful flux removal afterward, because residue can cause corrosion. Standard electronics rosin flux will not work.

Titanium and magnesium. Both oxidize readily and resist ordinary solders. They generally require special processes, plating before soldering, or an alternative joining method.

Cast iron. Its surface contains graphite and is often porous, which hampers wetting. Brazing or welding is usually used for cast iron repairs.

Chromium and chrome plating. Chromium oxide forms on the surface and blocks solder. The plating may sometimes be removed locally, or the joint may be made some other way.

Galvanized steel. It can be soldered with the right flux, but heating the zinc coating creates fumes that you should not breathe. Ventilation is essential and some work is better done by welding or by mechanical fastening. For the welding side of this, see the rest of this site.

High-alloy and exotic metals. Tungsten, tantalum, and similar metals are generally outside ordinary hobby soldering.

Metals that solder easily

Copper, brass, bronze, tin, tin-plated steel, silver, and gold are the typical easy ones. Many electronic parts are plated with tin or gold to make soldering easy. Mild steel can be soldered with a suitable flux. Our overview of soldering tools and materials explains which flux fits which job.

When a normally solderable metal refuses

Solder can fail on metals that normally accept it. Common causes:

  • Oxidation or tarnish. Old copper or brass may need cleaning with abrasive or acid-based cleaner before it will take solder.
  • Grease, oil, or finger marks. Clean with solvent or degreaser.
  • Coatings. Lacquer, paint, and clear coatings will block solder.
  • Wrong or old flux. Use a flux suited to the metal.
  • Not enough heat. If the joint is too cool or the iron is too small, the solder will not flow.
  • Dirty tip. A crusty tip transfers heat poorly. Clean and retin it.

If you ran into one of these problems after a bad attempt, how to fix a soldering mistake covers cleaning and re-doing a joint. Pewter and similar soft alloys are solderable but are easy to melt; see soldering and repairing pewter.

What to do instead

  • Use a special flux or solder designed for the metal (for example, products made for stainless steel or aluminum). Follow the manufacturer’s directions closely.
  • Plate or pre-tin the surface. Some metals are plated with nickel, tin, or copper first so solder has something to bond with.
  • Braze. Brazing uses higher heat and different filler metals. It is common for steel, cast iron, and some aluminum applications. See silver soldering for a hybrid process that sits between soldering and brazing.
  • Weld. For structural joints on aluminum, stainless steel, and titanium, welding is usually the proper route.
  • Fasten mechanically. Bolts, rivets, crimps, or clamps avoid the issue entirely. For electrical connections to aluminum or stainless, use connectors made for the purpose.

Safety note

Fumes from heated coatings, zinc, and some fluxes can be harmful. Use good ventilation, and check the label of any flux or solder you use. If you are unsure what an item is made of, test a hidden area first or have it identified before applying heat.

The complete guide to soldering

Soldering Tools and Materials: What You Need to Start
Read the guide

Keep exploring

Guides from other topics

All topics →