Soldering

Silver Soldering for Silversmithing and Jewelry

Learn how silver soldering works for jewelry and silversmithing: tools, solder grades, flux, pickle, step-by-step technique, common problems and safety.

On this page
  1. What silver soldering is
  2. What you need to solder sterling silver
  3. Solder grades and why they matter
  4. The four basic steps
  5. Step-by-step
  6. Common problems
  7. Safety
  8. How much does it cost to get jewelry soldered?
  9. Next steps

What silver soldering is

Silver soldering joins silver, copper, brass, and similar metals using a solder alloy that contains silver. Unlike electronics solder, it is heated with a torch, and it melts at a much higher temperature. The result is a strong joint that can withstand the stresses jewelry and silverware face in daily use.

Silver soldering vs silver brazing

The two terms overlap. By the widely used technical convention, a process is called soldering when the filler metal melts below roughly 450°C (840°F) and brazing when it melts above that. Jewelry “silver solder” melts well above that line, so by that definition it is technically brazing. In the jewelry trade, though, the word “soldering” is used for both, and “silver solder” is the normal name for the alloy. In industrial settings, “silver brazing” usually refers to silver-bearing filler alloys used on things like copper tubing or tooling. The technique is similar: clean metal, flux, a torch, and filler flowing into a tight joint.

What you need to solder sterling silver

  • A torch. Small propane, butane, or similar torches are common for jewelry. Larger work needs more heat.
  • Silver solder in hard, medium, and easy grades (see below).
  • Flux. Borax-based or commercial jewelry fluxes are typical. Flux keeps the metal from oxidizing while heating.
  • A soldering surface. A soldering block, charcoal block, or ceramic board that tolerates heat and does not draw it away too fast.
  • Tools to hold and place: tweezers (preferably heat-resistant), third-hand clamps, binding wire, and a small brush for flux and solder placement.
  • Pickle. A mild acid solution that removes flux residue and oxide after soldering. Typical choices are a commercial pickle compound or citric acid. Keep the pickle warm in a dedicated pot, away from food.
  • Safety gear: eye protection, ventilation, a fireproof work surface, and a nearby fire extinguisher.

Solder grades and why they matter

Silver solders are sold in grades usually called hard, medium, and easy (sometimes “extra-easy”). The names reflect melting temperature. Hard solder melts at the highest temperature and easy at the lowest, but all of them melt below the point where sterling silver itself starts to melt.

This is useful because a piece often needs several joints. You start with hard solder, then use medium, then easy for later joints, so earlier joints do not melt when you heat the piece again. Exact temperatures vary by manufacturer, so check the supplier’s data sheet rather than relying on a general number.

The four basic steps

Beginners often hear soldering described in four steps. For silver, they are:

  1. Prepare: fit and clean the joint.
  2. Flux: coat the joint and place the solder.
  3. Heat: bring the whole piece up to temperature until the solder flows.
  4. Clean: quench (if appropriate), pickle, rinse, and finish.

Step-by-step

1. Fit the joint. The seam should close tightly, with no visible gap. Solder fills very small gaps by capillary action but does not bridge wide ones. If light shows through the seam, refit it.

2. Clean the metal. Remove oil, polish, and tarnish with fine abrasive and a degreasing wash. Solder will not flow over dirty metal.

3. Apply flux. Brush flux over the seam and surrounding area.

4. Place solder. Cut small pieces (often called pallions) and set them along or beside the seam. Using too much is a common beginner mistake. Excess solder is hard to remove and leaves a lump to file away.

5. Heat the piece, not the solder. Use a broad, soft flame and keep it moving, warming the whole piece. Flux will first bubble, then go clear and glassy. Continue heating until the metal reaches the right temperature. Solder should then melt and flow along the seam toward the hottest area. Pull the flame away as soon as the solder flows.

6. Quench and pickle. After the metal has cooled slightly, it is often quenched in water, and then placed in warm pickle to remove oxidation and flux. Use brass or plastic tongs rather than steel tweezers, as steel can cause copper to plate onto the silver.

7. Rinse and finish. Rinse well, then file, sand, and polish the joint.

Common problems

  • Solder balls up and will not flow. Usually the metal is dirty, there is not enough flux, or the piece is not evenly hot. Clean, reflux, and heat the whole piece.
  • Solder flows to the wrong place. Solder moves toward heat. Direct the flame so the seam is the hottest part.
  • A joint reopens when soldering a second joint. The same grade of solder was reused, or the piece got too hot. Use a lower-melting grade for later joints.
  • Pits or holes in the seam. Often caused by overheating or old flux. Keep the heat controlled.
  • Dark surface stain (fire scale). Sterling silver contains copper, which oxidizes when heated. Flux coatings or anti-firescale products can reduce it, and it is polished away afterward.
  • The silver slumps or melts. The piece was overheated. Thin sheet and wire are especially vulnerable, so watch for the surface turning glossy or wet-looking and back off.

If a joint goes badly, the broader troubleshooting advice in how to fix a soldering mistake applies in principle, though the torch and solder are different.

Safety

  • Use good ventilation. Flux fumes and heated metal can be irritating.
  • Some older silver solders contained cadmium, which is toxic when heated. Many suppliers now sell cadmium-free solders. Check the label on any old stock and avoid using solder that contains cadmium.
  • Keep flammables away, tie back long hair, and have a fire extinguisher nearby.
  • Handle pickle and any acids according to the supplier’s instructions, and never use pickle in a food container.

For a broader look at kit and consumables, see soldering tools and materials.

How much does it cost to get jewelry soldered?

Prices vary by region, the jeweler, and the complexity of the job. A simple repair, such as closing a broken ring shank or a jump ring, is typically among the cheaper jewelry services. Work that involves resizing, stone settings, or delicate antique pieces costs more, and some jewelers quote after inspecting the piece. Ask for a quote before you commit, and ask whether the price covers polishing and any stone protection.

Next steps

Practice on scrap sterling or copper sheet before working on a finished piece. Practice making a simple closed band first, then move to more complicated assemblies using hard, medium, and easy solder in sequence.

The complete guide to soldering

Soldering Tools and Materials: What You Need to Start
Read the guide

Keep exploring

Guides from other topics

All topics →