Soldering

How to fix a soldering mistake?

Fix a bad solder joint by reheating with flux, removing excess with braid or a pump, and redoing it cleanly. Covers cold joints, bridges and lifted pads.

On this page
  1. Short answer
  2. Basic repair steps
  3. Fixes by type of mistake
  4. Fixing mistakes outside electronics
  5. Preventing mistakes next time
  6. When to stop

Short answer

Most soldering mistakes are fixable. The usual approach is to reheat the joint, add a little flux and fresh solder so it flows properly, remove any excess with desoldering braid or a pump, then let it cool without moving it. If the joint is badly contaminated, remove the old solder completely, clean the area, and solder it again.

Basic repair steps

  1. Clean and tin the iron tip. A dirty or oxidized tip transfers heat poorly and is a common cause of bad joints. Wipe it and add a little fresh solder.
  2. Clean the joint. Remove residue and dirt. On electronics, isopropyl alcohol and a small brush work well.
  3. Add flux. Fresh flux helps solder flow again. Flux-core solder already has some, but extra flux often helps with a stubborn joint.
  4. Heat both surfaces. Touch the iron to both parts, such as the component lead and the board pad, so they heat together.
  5. Feed in a little fresh solder. Apply it to the heated joint, not the tip of the iron.
  6. Remove the solder first, then the iron. Do this promptly to avoid overheating.
  7. Let it cool undisturbed. Moving the joint while it solidifies is a common cause of a cracked or dull joint. Do not blow on it to speed things up.
  8. Clean off flux residue if the flux requires it.

Fixes by type of mistake

Cold or dull, grainy joint. The solder did not fully melt or the parts moved as it cooled. Reheat it, add a small amount of flux and fresh solder, and let it flow into a smooth shape.

Cracked or loose joint. Reflow it the same way. If it fails again, desolder it and start fresh.

Too much solder. Reheat the joint and remove the excess with desoldering braid pressed against the joint with the iron, or with a solder pump. Wipe the tip so you do not drop solder back onto the work.

Solder bridge between pins or pads. Add a bit of flux, then draw the bridge away with braid or drag a clean iron tip through the gap. Check with a magnifier afterward, and with a meter if you can, to confirm there is no short.

Too little solder. Reheat the joint and feed in a small amount more. The solder should wet the whole joint, not sit as a ball on one side.

Solder balled up and not sticking. Usually the metal is dirty, oxidized, or not hot enough, or the wrong flux is in use. Clean the surfaces, add flux, and reheat. If the metal will not accept solder at all, see what metals solder will not stick to.

Contaminated or oxidized joint. Remove the old solder with braid or a pump, clean the pad and lead, and resolder with fresh solder and flux.

Lifted pad or torn trace on a circuit board. This is more serious. Excessive heat or force can lift copper off the board. A small jumper wire to the next connection point is a common fix. If the damage is extensive, it may not be worth repairing.

Overheated or damaged component. Heat can damage components. If a part is discolored, melted, or no longer working, it generally needs to be replaced. Next time, limit the iron contact time and use a heat sink clip where appropriate.

Wrong component or placement. Desolder it, clean the holes or pads, and fit the correct part. A solder pump can clear through-holes.

Fixing mistakes outside electronics

Copper pipe joints. If a joint leaks, do not just add more solder over it. Drain the line completely so there is no water in the joint, heat the fitting, separate it, clean everything back to bright metal, flux, and solder it again. Overheated flux that has turned black or burned is a common cause of failure. See how to solder copper pipe joints step by step.

Jewelry seams. If the solder balled up or the seam did not fill, let the piece cool, clean it, add fresh flux, and heat the whole piece evenly. Piling on solder rarely fixes a poorly fitted seam. See silver soldering for jewelry.

Pewter. If a piece slumped or melted, stop and let it cool. It may be possible to support and rebuild the area, but avoid more heat until you have a plan. See soldering and repairing pewter.

Preventing mistakes next time

  • Use the right tools for the job; see soldering tools and materials.
  • Keep the tip clean and tinned.
  • Clean the metal and use the correct flux.
  • Heat the parts, not the solder.
  • Hold the work still until the solder has set.
  • Check the temperature. Leaded and lead-free solders need different heat; see leaded vs lead-free solder.
  • Practice on scrap.

When to stop

If a joint keeps failing, stop and reassess instead of adding more heat. Repeated heating can damage components, pads, and the workpiece. Let everything cool, clean it all, and try again, or consider whether another approach would work better.

The complete guide to soldering

Soldering Tools and Materials: What You Need to Start
Read the guide

Keep exploring

Guides from other topics

All topics →