Pipe Welding

Welding Stainless, Nickel Alloy and Clad Pipe

An overview of welding sanitary stainless dairy pipe, Hastelloy, Monel and clad pipe: common processes, cleanliness, purging, filler choice and cautions.

On this page
  1. What these materials have in common
  2. Stainless steel dairy and sanitary pipe
  3. Hastelloy pipe
  4. Monel pipe
  5. Clad pipe
  6. Weld overlay vs cladding
  7. General tips

What these materials have in common

Stainless steel, nickel alloys such as Hastelloy and Monel, and clad pipe are chosen for corrosion resistance, cleanliness or high-temperature performance. They tend to be more demanding to weld than carbon steel. The usual themes are:

  • Cleanliness. Oil, grease, paint, markers and iron contamination can cause defects or reduce corrosion resistance. Many shops use dedicated stainless brushes and tools for these materials.
  • Controlled heat input. Too much heat can harm corrosion resistance or cause distortion and cracking.
  • Gas protection. The weld pool and, on open-root pipe joints, the inside of the pipe are normally protected with inert gas (a “purge”) to prevent heavy oxidation.
  • Correct filler metal. The filler is selected for the base metal and service, usually from a qualified procedure.

TIG (GTAW) is the most common process for the root pass on these materials, followed by TIG, stick or other processes for fill and cap, depending on the procedure. If you are newer to pipe work, start with the basic pipe welding process first.

Stainless steel dairy and sanitary pipe

Dairy, food, beverage and pharmaceutical piping is typically stainless steel tube or pipe, welded so that the inside surface is smooth. Crevices, pits and rough weld metal can harbor bacteria and are hard to clean.

Points commonly emphasized for sanitary work:

  • Process. Autogenous or filler-added TIG welding is common, and many shops use orbital welding equipment for consistent, repeatable welds.
  • Purging. The inside of the tube is usually purged with argon so the weld root is not heavily oxidized (“sugared”). Oxide on the inside surface can hurt corrosion resistance and cleanability.
  • Fit-up. Tight alignment and square, clean cut ends matter, because there is little room to correct a mismatch.
  • Weld profile. The goal is full penetration with a smooth inside bead and no crevices.
  • Finishing. Welds are often cleaned or passivated afterward, and inspected visually and sometimes with a borescope.
  • Standards. Industry or customer standards, such as those for hygienic piping, can set acceptance criteria, so check what applies to your job.

The common stainless grades for these systems are austenitic types such as 304 and 316L, although the project specification governs.

Hastelloy pipe

Hastelloy is a family of nickel-based alloys known for resistance to many corrosive chemicals. Grades such as C-276 and C-22 are used in chemical processing.

Common considerations:

  • GTAW is widely used, with matching or overmatching nickel-alloy filler specified for the grade.
  • Keep heat input low and control interpass temperature, as the procedure directs.
  • Nickel alloys have a more sluggish puddle than carbon steel, so the weld does not flow out as much. Welders place the metal where it is needed and often use smaller beads.
  • Cleanliness is critical. Contamination, particularly from sulfur-bearing compounds such as some marking pens and cutting fluids, can cause cracking in nickel alloys.
  • Exact filler, shielding gas and post-weld requirements are specific to grade and service, so follow the manufacturer’s recommendations and the qualified WPS.

Monel pipe

Monel is a nickel-copper alloy with good corrosion resistance, including to seawater and some acids. Monel 400 is the grade most people encounter.

  • It is generally welded with GTAW, and also with other arc processes in some cases, using filler metal developed for the alloy.
  • As with other nickel alloys, clean the joint area thoroughly and keep heat input moderate.
  • Monel can look similar to some stainless steels. A magnet is not a reliable way to identify it, since cold working and composition can change magnetic response. Check the material certificates or ask the supplier if you are unsure what you have.

Clad pipe

Clad pipe has a base of carbon or low-alloy steel for strength, with an internal layer of corrosion-resistant alloy such as stainless steel or a nickel alloy. It is used where the fluid is corrosive but a solid alloy pipe would cost too much, as in some oil and gas applications.

Welding clad pipe usually involves two steps at each joint:

  1. The carbon steel backing is welded with a suitable filler.
  2. The inner alloy layer is restored with a corrosion-resistant filler so the inside surface is continuous. This can mean a transition between filler types in the weld, and a careful choice of root and first passes to limit dilution from the carbon steel.

Controlling iron pickup in the alloy layer is a major concern. Clad pipe procedures tend to be detailed, and welders are normally qualified on the specific procedure.

Weld overlay vs cladding

The two terms are related but not identical:

  • Cladding refers to a corrosion-resistant layer bonded to a base metal, which can be done by processes such as roll bonding or explosion bonding. The pipe or plate arrives with the layer already attached.
  • Weld overlay (also called weld cladding) deposits corrosion-resistant weld metal onto a base metal surface, for example on the bore of a pipe or fitting, using welding. A related surfacing technique for wear resistance is hardfacing.

You may see both used to describe pipe with an alloy lining, so check which is meant. In practice, the joint between two lengths is usually completed with a welded lining at the girth weld.

General tips

  • Get the WPS and material certificates before starting, and do not substitute filler metals.
  • Practice on scrap of the same material, since puddle behavior differs from carbon steel.
  • Keep stainless and nickel-alloy tools separate from those used on carbon steel.
  • Wear appropriate respiratory protection and ensure ventilation. Fumes from stainless and nickel alloys may contain hazardous metals such as chromium and nickel.
  • Qualification tests are specific to the material and process. A carbon steel pass, such as in the 6G pipe welding test, does not automatically cover stainless or nickel alloys.

For which process fits which job, see what type of welding do pipe welders use?

The complete guide to pipe welding

Pipe Welding Process: Root, Hot, Fill and Cap Passes
Read the guide

Keep exploring

Guides from other topics

All topics →