Pipe Welding

Pipe Welding Positions: Stovepipe, Uphill and Overhead

Learn how pipe welding positions work: 1G, 2G, 5G and 6G, stovepipe (downhill) welding, uphill travel, and overhead pipe welding tips for beginners.

On this page
  1. The short answer
  2. Pipe welding position designations
  3. What “stovepipe” welding means
  4. Uphill vs downhill
  5. Overhead pipe welding
  6. If you mean welding a wood stove flue
  7. Tips for practicing

The short answer

On pipe, the position tells you how the pipe is oriented and whether it can be turned while you weld. In a fixed position, the welder moves around the pipe, so a single joint passes through flat, vertical and overhead sections. “Stovepipe” is a nickname for the downhill vertical technique traditionally used on pipelines. Overhead is the hardest part of a fixed-pipe weld, where you weld upward at the underside of the joint.

Pipe welding position designations

Pipe positions are usually named with a number and the letter G (groove weld). For plate and general positions, see welding positions and techniques. The common ones are:

  • 1G: The pipe is horizontal and rotated while you weld on top in the flat position.
  • 2G: The pipe is vertical, and the weld runs horizontally around it.
  • 5G: The pipe is horizontal and fixed. You weld around it, so you go through flat, vertical and overhead sections.
  • 6G: The pipe is fixed at about 45 degrees, and the weld passes through all positions at a changing angle. It is widely seen as the most demanding standard test position.

Different codes use slightly different wording, so the governing standard for your test or job is the final word. For more on the test most welders aim for, see the 6G pipe welding test.

What “stovepipe” welding means

In pipeline work, stovepipe welding generally means making a weld on a horizontal fixed pipe (5G) by travelling downhill, from about 12 o’clock to 6 o’clock on each side. The welder usually runs a fast-freezing cellulosic electrode such as E6010 for the root and hot passes, with a low-hydrogen electrode such as E7018 sometimes used afterward. Downhill travel is fast, which is why it is associated with long pipelines, where thousands of joints need to be welded.

The trade-off is that downhill welding on stick carries a greater risk of lack of fusion if the heat is too low or the travel is too fast, and some codes and procedures restrict it, especially on thicker walls or critical service. In some regions, welders are tested for uphill instead. Which direction is permitted comes from the WPS and code for the job.

Uphill vs downhill

  • Downhill: Faster, usually used on thinner-wall pipe or cross-country pipelines. Slag and the puddle can run ahead of the arc if the travel is too slow.
  • Uphill: Slower and more controlled, common on thicker walls, in plants and refineries, and in many certification tests. Heat input is typically higher and the welder builds the bead from the bottom up. Technique for climbing a joint is in vertical up welding.

Neither is “better” in general. The right one is the one your procedure and code call for. For how these fit into the larger sequence of passes, see the pipe welding process from root to cap.

Overhead pipe welding

On a fixed pipe, you cannot avoid the overhead section at the bottom of the joint. It is hard because gravity pulls the molten puddle away from the joint, and you are often working in a cramped spot with sparks and spatter falling toward you.

Tips that are commonly given for overhead work on pipe (see also overhead welding: technique, settings and safety tips):

  • Keep the puddle small. A smaller, cooler puddle freezes sooner and is less likely to sag. Pausing briefly to let it cool is a common technique with TIG and stick.
  • Use the right filler or electrode size. Smaller diameters are often easier to control overhead.
  • Control the angle. Dragging or pushing too steeply can cause slag to run ahead or poor fusion. Small adjustments in angle matter as the pipe curves.
  • Mind your posture. Awkward posture adds fatigue, and fatigue ruins consistency. Set up so you can move smoothly through the position.
  • Clean thoroughly between passes. Slag is harder to see and remove in awkward places.
  • Protect yourself. Overhead work means hot spatter falling onto clothing. Wear a cap, a jacket or sleeves rated for welding, and buttoned collars.

Good fit-up helps more than anything else, since a consistent gap and well-feathered tacks make the overhead section far easier. See pipe fit-up.

If you mean welding a wood stove flue

“Stove pipe welding” also gets searched by people working on residential wood stoves and chimneys. This is a different job from pipeline welding. The pipe is usually thin, so the main risk is burning through it.

  • Put most of the heat on the thicker part (such as a stove body or collar) and keep the arc off the thin pipe wall as much as possible.
  • If the flue is badly rusted, pitted or burned out, replacing the section is generally safer than patching it.
  • A weak or leaking flue connection can allow smoke or carbon monoxide into the house, so if you are unsure about the job, ask a qualified welder or installer and follow local codes for solid-fuel appliances.

Tips for practicing

  • Start with 1G (rotated) to learn bead control, then try 2G and 5G.
  • Practice on short pipe coupons rather than long lengths. Small diameters force quick position changes.
  • Mark clock positions on the coupon so you can note where problems tend to happen.
  • Cut up your practice welds to check for lack of fusion, not just appearance.

The complete guide to pipe welding

Pipe Welding Process: Root, Hot, Fill and Cap Passes
Read the guide

Keep exploring

Guides from other topics

All topics →