This article is a general overview. Equipment differs between makers, so your torch, regulator and cylinder manuals take priority over anything here. If you have never done this before, ask a trained instructor or an experienced welder to go through it with you in person.
Before you start
- Work in a ventilated area, away from flammable materials, with a fire extinguisher nearby.
- Wear tinted goggles made for gas welding, along with gloves, a long-sleeved cotton or wool shirt and sturdy shoes.
- Keep oil, grease and greasy gloves away from oxygen cylinders, regulators and fittings. Oxygen can make them ignite violently.
- Inspect the equipment: hoses should not be cracked or burnt, fittings should be undamaged, and regulators should be rated for the gas they connect to.
- Secure cylinders upright with a chain or strap, on a cart or against a wall. Acetylene cylinders should be stored and used upright.
Setup steps
- Crack the cylinder valves briefly. Stand to the side, away from the valve outlet, and open each cylinder valve for a moment to blow out dust, then close it. Do this with acetylene only in a well-ventilated area, away from any ignition source.
- Attach the regulators. Fit the oxygen regulator to the oxygen cylinder and the acetylene regulator to the acetylene cylinder. Tighten the nuts with a proper wrench, without forcing them. Fittings are designed so that the wrong regulator generally does not fit, so do not try to adapt them.
- Back the regulator adjusting screws out. Turn each adjusting screw counterclockwise until it is loose, so no pressure is set before you open the cylinder.
- Connect the hoses. Connect the oxygen hose (green in North America) to the oxygen regulator, and the fuel hose (red in North America) to the acetylene regulator. The fuel fittings typically have left-hand threads. Fit flashback arrestors and check valves, either at the regulator, at the torch, or both, as the manufacturer recommends.
- Attach the torch. Connect the hoses to the torch handle, then fit the welding attachment and a suitable tip. For tip selection, see choosing the right oxy-acetylene tip size.
- Open the cylinder valves slowly. Open the oxygen valve fully, and the acetylene valve only about a quarter to a half turn, so you can shut it off quickly in an emergency. Keep your face and body away from the regulator gauges as you open them.
- Set the working pressures. With the torch valves closed, adjust each regulator to the pressure recommended for your tip and torch. Do not set acetylene above its safe limit, commonly given as 15 psi (about 1 bar).
Leak testing
Check every connection for leaks before lighting. Use a leak-detection solution or soapy water, not a flame, and watch for bubbles at connections and the torch. If you find a leak, close the cylinder valves, vent the system, and tighten or replace the faulty parts. Many setups also have a pressure-hold check: set the pressure, close the cylinder valve, and see whether the gauge falls. Follow your manual for this.
Lighting
- Purge each line. Briefly open each torch valve, one at a time, to clear air from the hoses, then close it. Do this in a ventilated place.
- Open the acetylene valve on the torch slightly. Open it about a quarter turn.
- Light with a striker. Hold the striker at the side or in front of the tip, never use a butane lighter, and keep it pointed away from yourself and others. The flame will be yellow and sooty.
- Increase acetylene until the flame just stops smoking.
- Open the oxygen valve slowly. Add oxygen until you reach the flame you want. Our guide to the neutral, carburizing and oxidizing flames explains what to look for.
Shutdown
- Close the acetylene torch valve first, then the oxygen torch valve, which stops the flame. Some manufacturers specify the order; follow yours.
- Close both cylinder valves.
- Open the torch valves to bleed the gas in the hoses and regulators, until both gauges read zero, then close the torch valves.
- Back out the regulator adjusting screws.
- Coil the hoses and store the torch so it cannot be knocked or burnt.
Common mistakes
- Using oil or grease on oxygen fittings.
- Using acetylene above its pressure limit.
- Opening the acetylene cylinder valve too far, which makes it hard to close quickly.
- Skipping the leak test.
- Lighting in a closed space with gas leaking.
- Standing in front of a regulator when opening a cylinder.
- Ignoring a flashback or a loud popping flame. If it happens, close the valves and find out why before continuing.
For the bigger picture of how the process works, see our gas welding overview.