Gas and Forge Welding

Choosing the Right Oxy-Acetylene Tip Size for Metal Thickness

How to pick an oxy-acetylene welding tip size for the metal thickness: why numbering differs by brand, how to use a maker's chart, and signs a tip is wrong.

On this page
  1. Short answer
  2. Why tip size matters
  3. Numbering differs by brand
  4. Matching tip to thickness
  5. Welding tips versus cutting and heating tips
  6. Signs the tip is wrong
  7. Care of tips

Short answer

Choose the tip according to the thickness of the metal and use the tip manufacturer’s chart for the exact number and gas pressures. Thin metal needs a small tip, because it delivers less heat and a smaller flame. Thick metal needs a larger tip. Tip numbers are not standardised across brands, so a “number 3” from one maker is not necessarily the same as a “number 3” from another.

Why tip size matters

The tip’s orifice size controls how much gas flows and therefore how much heat the flame delivers. If you choose a tip that is:

  • Too small, the flame does not heat the metal enough. The puddle forms slowly or not at all, and you may be tempted to turn the pressures up, which can make the flame harsh and noisy.
  • Too large, the heat is excessive. On thin sheet you will burn through, warp the part or blow holes in it.

The correct tip gives a controllable puddle at a sensible travel speed without overheating the surrounding metal.

Numbering differs by brand

Most torch makers number their tips in a series, and on common systems a larger number means a larger orifice and more gas flow. The sequence, the thickness range each number covers, and the recommended pressures all differ between brands and between torch series. Tips are also often not interchangeable between manufacturers, because the seats and threads differ.

So do not rely on a chart you found for another brand, or a number quoted in a forum. Look up the chart for your torch’s make and model, which is usually printed in the manual or on the maker’s website, and sometimes stamped or packaged with the tips.

Matching tip to thickness

As a general principle:

  • Thin sheet metal (body panels, small tubing) needs one of the smallest tips in the series.
  • Light to medium sheet and tube calls for a small to mid-sized tip.
  • Plate needs larger tips, and past a certain thickness it is usually better to bevel the joint, preheat, or use another process (see welding processes and equipment).

Consider more than thickness:

  • Metal type. Copper and aluminium draw heat away quickly and often need a larger tip than steel of the same thickness.
  • Joint design. Butt joints on thin sheet need less heat than tees or laps of the same material.
  • Part size. A large mass of metal acts as a heat sink and may need more heat or preheating.
  • Technique. Leftward welding on thin metal generally works with a smaller tip than rightward welding on thick metal; see our gas welding overview.

Welding tips versus cutting and heating tips

Welding tips, cutting tips and heating tips are different parts with different designs. A cutting tip has a ring of preheat holes and a separate cutting oxygen jet and is not a welding tip. Heating nozzles spread the flame over a wider area. Use the right tip for the job, and the right size within each type. Propane and other fuels also need tips made for them; see do you use propane gas for welding.

Signs the tip is wrong

  • Burn-through, holes and a puddle that runs away: tip likely too big, or you are travelling too slowly.
  • Puddle will not form, or the weld sits on top without fusing: tip likely too small.
  • Flame popping, backfiring or whistling: may be a dirty, damaged or overheated tip, or pressures set outside the tip’s range.
  • A flame that is hard to hold neutral: check the pressures against the chart; see oxy-acetylene flame types.

Care of tips

Tip orifices clog with carbon and spatter. Clean them with tip cleaners of the correct gauge, not with drill bits or wire, and handle them gently, because a damaged orifice produces a distorted flame. Fit the tip firmly according to the manufacturer’s instructions, check for leaks as described in how to set up and light an oxy-acetylene torch, and replace tips that are cracked, flared or worn.

The complete guide to gas and forge welding

Gas Welding: How Oxy-Acetylene Welding Works
Read the guide

Keep exploring

Guides from other topics

All topics →