Gas and Forge Welding

Thermite Welding: How the Crucible Process Works

What a welding crucible is and how thermite welding uses one: the aluminium-iron oxide reaction, mould and preheat, rail uses, and key safety cautions.

On this page
  1. What “crucible” means in welding
  2. How thermite welding works
  3. Steps in rail welding
  4. Where it is used
  5. Can I melt steel in a crucible?
  6. Safety
  7. Related reading

What “crucible” means in welding

A crucible is a container made of heat-resistant (refractory) material that can hold metal at very high temperatures. The word is used in more than one way around welding, so it helps to know which meaning you are after:

  • In thermite welding, the crucible is the vessel where the reaction takes place and from which molten steel is poured into a mould around the joint.
  • In foundry and hobby casting, a crucible is a pot, often graphite or clay-graphite, used in a furnace to melt metals such as aluminium, brass or bronze.

This article is about the first meaning. It is a process most people meet through railway track repair rather than in a home workshop.

How thermite welding works

Thermite is a powder mixture of a metal fuel, classically aluminium, and a metal oxide, classically iron oxide. Once ignited, the aluminium takes oxygen from the iron oxide in a strongly exothermic reaction. The products are aluminium oxide (slag) and molten iron. In practice, welding portions contain added alloying elements so the resulting steel suits the work, and the reaction can reach temperatures of well over 2,000°C.

Because the reaction makes its own heat and its own molten metal, the process needs no electrical supply and no gas torch for the reaction itself. A torch is often used for preheating, though; see our gas welding overview for how that equipment works.

Steps in rail welding

The rail version is the best-known, and the general sequence is:

  1. Align and gap the rail ends. The ends are positioned with a specified gap, with the correct alignment for height and direction.
  2. Fit a mould. A refractory mould, usually made of sand, is clamped around the joint and sealed.
  3. Preheat. The rail ends are heated, often with a gas torch, so the molten steel will fuse with them rather than freeze on contact.
  4. Ignite the portion in the crucible. The reaction runs for a short period and the slag separates from the steel.
  5. Tap the steel. The crucible releases the molten steel into the mould, where it fills the gap and fuses with the rail ends.
  6. Cool, trim and grind. The excess metal is removed and the head of the rail is ground to the correct profile.

The exact procedure depends on the portion and mould system, so crews follow the manufacturer’s procedure and the railway’s own standards.

Where it is used

Thermite welding is used to join rails in the field, to repair damaged sections of track, and in some other heavy repair situations where moving the part to a shop is impractical. A related application is exothermic bonding of copper conductors for grounding systems, which uses a similar chemical principle on a small scale and a reusable graphite mould.

Can I melt steel in a crucible?

A crucible suitable for steel needs a furnace that gets well above the melting point of steel. A typical hobby propane furnace may do aluminium and bronze but not steel, and pots made for non-ferrous metal can fail if pushed too hard. People who ask this question are often better served by learning to cast the lower-melting metals first. If your goal is joining steel, there are far simpler methods than melting it yourself, such as torch welding or forge welding.

Safety

Thermite produces molten metal and intense heat in seconds, and moisture trapped in a mould or crucible can cause violent steam eruptions. This is professional work done by trained crews with the right protective equipment and procedures. It is not a casual home project, and the hazards are not worth taking on without training and proper supervision.

If you are exploring the different ways metal is joined with heat, start with how oxy-acetylene gas welding works, then compare it with torch brazing and bronze welding.

The complete guide to gas and forge welding

Gas Welding: How Oxy-Acetylene Welding Works
Read the guide

Keep exploring

Guides from other topics

All topics →