Projects and Repairs

How to Build a Welding Cart: Plans, Materials and Cut List

Build a welding cart from square steel tube: planning around your machine and gas cylinder, materials, an adjustable cut list, assembly steps and safety tips.

On this page
  1. Plan the cart around your equipment
  2. Materials and tools
  3. Example cut list (adjust to fit)
  4. Step-by-step build
  5. Cylinder safety
  6. Upgrades

A welding cart is one of the best early projects. It is useful the day it is finished, it uses simple joints, and it forces you to practice squaring, tacking and distortion control. It is also forgiving: if one weld is ugly, the cart still works.

Plan the cart around your equipment

Do not copy someone else’s dimensions blindly. Start by measuring your own kit.

  • Machine footprint. Measure the length, width and height of the welder, and note the weight. The top shelf should be slightly larger than the machine’s base, with a lip or stops so it cannot slide off.
  • Gas cylinder. Measure the diameter and height of the cylinders you use. The cylinder rest needs to hold the bottle upright and be tall enough to be secured with a chain or strap.
  • What else you need to store. Think about the torch or gun, ground clamp and leads, helmet, gloves, spare consumables and a few hand tools. Hooks and a small shelf or drawer are cheap additions.
  • Where you will use it. A cart that rolls on a smooth shop floor can use small casters. If you work on gravel or rough ground, you will want larger wheels.
  • Your height. Pick a top-shelf height that lets you reach the controls without stooping.

Sketch the plan, including each shelf’s height, before you cut anything.

Materials and tools

Materials (quantities depend on your design):

  • Square steel tube for the frame. A common choice is mild steel square tube in a moderate wall thickness, but pick a size and thickness based on the weight of your machine and cylinder.
  • Steel sheet or plate (or expanded metal or wood) for the shelves. Steel is durable and non-flammable. If you use wood, keep it away from the weld spatter zone.
  • Flat bar or angle for the cylinder cradle, shelf lips and brackets.
  • Casters. Heavy-duty, rated well above the total load, with at least two that lock. Rigid and swivel casters are often combined.
  • A chain or strap to secure the cylinder.
  • Fasteners, hooks and paint or primer.

Tools: a chop saw or angle grinder for cutting, a square, tape measure, clamps or magnets, a welder, a drill, and the usual safety gear.

Example cut list (adjust to fit)

These dimensions are an illustration for a two-shelf cart carrying a typical small welder and one cylinder. They are a starting point only, so change them to suit your own measurements.

Part Qty Approximate length Notes
Vertical legs (square tube) 4 about 34 in Sets the overall height
Upper frame, long sides 2 about 30 in Machine shelf perimeter
Upper frame, short sides 2 about 18 in Machine shelf perimeter
Lower frame, long sides 2 about 30 in Lower shelf perimeter
Lower frame, short sides 2 about 18 in Lower shelf perimeter
Shelf panels 2 to fit frame Sheet steel or similar
Cylinder cradle and ring 1 set to fit cylinder Flat bar bent or cut to wrap the cylinder
Handle 1 about 18 in Tube or bar at one end
Casters 4 n/a Rated above total load

Subtract tube thickness when you cut pieces that fit between legs, so the finished frame comes out to the dimensions you want.

Step-by-step build

  1. Cut all pieces and deburr the ends. Check each cut is square. Mismatched lengths show up later as a wobbly cart.
  2. Build the two end frames. Lay two legs and two cross pieces flat on a level surface. Square them, clamp, and tack the corners.
  3. Check for square by comparing diagonals. Fix any error now, before welding fully.
  4. Join the end frames with the long rails. Tack, then re-check square and level.
  5. Weld fully, in short runs. Alternate sides and move around the frame so heat does not pull it out of shape.
  6. Add shelf supports and shelves. Weld small angle or bar supports, then drop in or weld the shelf panels. Add a lip around the top shelf.
  7. Build the cylinder cradle. Weld a base or stop at the bottom and a ring or bracket higher up for the chain or strap. Test the fit with the actual cylinder.
  8. Attach casters. Weld or bolt mounting plates to the leg bottoms. Bolted plates make casters easier to replace.
  9. Add handle and hooks for leads and hose.
  10. Grind sharp edges, clean and paint. Remove spatter and sharp corners, degrease, prime and paint to prevent rust.

Cylinder safety

  • Always secure a gas cylinder upright with a chain or strap. A falling cylinder can be dangerous, particularly if the valve breaks off. More on this in storing and securing welding gas cylinders.
  • Cap the cylinder when moving it, and keep the cart on level ground.
  • Do not store the machine in a way that hides cylinder or hose damage.
  • Keep the cart’s load within the casters’ rating, and lock the casters when you are welding.

Upgrades

  • Add a drawer, tool tray or a magnetic strip.
  • Add a pegboard panel for accessories.
  • Add a second shelf for a plasma cutter or an air compressor, if the frame can handle the extra weight.
  • Add a vise or a small work surface.

For other builds that grow from this one, see welding project ideas, or try a steel fire pit for practice with plate.

The complete guide to projects and repairs

Welding Project Ideas for Beginners and Hobbyists
Read the guide

Keep exploring

Guides from other topics

All topics →