Projects and Repairs

Welding a Steel Fire Pit: Materials and Step-by-Step Build

Build a steel fire pit by welding: choose plate thickness, avoid coated steel, add drainage and airflow, weld the seams, and finish with high-temperature paint.

On this page
  1. Design choices
  2. Materials and tools
  3. Safety and legal notes
  4. Step-by-step build
  5. Finishing and care
  6. Common mistakes

A steel fire pit is a satisfying beginner-to-intermediate project. It needs only straight cuts and long, simple seams, it makes a useful object, and heat distortion teaches you quickly how steel behaves. Before you start, read the safety notes below, because a fire pit involves both welding and open flame.

Design choices

  • Shape. Round bowls and rings are classic, but a square or rectangular box made from flat plate is easier to cut and fit. A ring can be cut from plate or rolled from a strip by a metal shop.
  • Size. Choose a diameter or width that suits the space and the people using it, and keep the sides low enough to sit around comfortably. Larger pits need more material and thicker sides to resist distortion.
  • Open or enclosed. A simple open bowl or box is easiest. Ventilation holes, a grate or a lift-off insert can improve airflow.
  • Portable or fixed. Legs, a base ring or a ground-level liner each change how much steel and how many joints you need.

Materials and tools

Steel. Mild or hot-rolled steel plate is the usual choice. Many builders use something in the range of about 1/8 in to 3/16 in for the walls and a similar or slightly thicker plate for the base. Thinner sheet is easier to cut and weld but warps more under repeated heat; thicker plate lasts longer but is heavier and needs more welding power. Pick a thickness your welder can penetrate.

Avoid galvanized, plated and coated steel. Heating zinc coatings releases fumes that are hazardous to breathe, and coated steel can also give off harmful fumes when used in a fire pit. Use bare steel. Do not use old tanks, drums or containers that held fuel or chemicals, or pressurized vessels, because of fire and explosion risk.

Also needed:

  • Square tube or bar for legs, a base frame or a grate
  • A welder: MIG, flux-core, stick or TIG can all work on this thickness
  • Angle grinder with cutting and flap discs, a chop saw or plasma cutter for cutting plate
  • Clamps, welding magnets, a square, tape measure and a marker or soapstone
  • A drill for drain holes
  • High-temperature paint or a suitable finish
  • Standard welding safety gear: auto-darkening helmet, gloves, long sleeves, eye and hearing protection, and a respirator when grinding
  • Place the finished pit on a non-combustible surface, away from structures, overhanging branches, fences and anything that can ignite. Do not use it on a wooden deck.
  • Check local rules. Many areas restrict open burning or have burn bans, particularly in dry seasons.
  • Keep a way to put the fire out nearby, and never leave it unattended.
  • Weld in a clear area away from dry grass, fuel and clutter, and have a fire extinguisher at hand.
  • Wear protective gloves when handling cut steel, which has sharp edges and is hot after welding.

Step-by-step build

  1. Plan and mark. Draw the design and mark all cut lines. For a box, you need four sides and a base. For a ring, determine the circumference from the diameter.
  2. Cut the pieces. Cut with a chop saw, grinder or plasma cutter. Grind the edges smooth, and bevel the edges of thicker plate where two pieces meet if you want the weld to penetrate more fully.
  3. Fit up. Clamp or magnet the sides together on a flat surface. Use a square to check the corners and keep the sides plumb.
  4. Tack. Place tacks at the corners and spaced along each seam. Re-check squareness. Fix errors now.
  5. Weld the seams. Weld in short runs, alternating sides and moving around the piece so heat does not build up in one spot and pull the shape out of line. For a fire pit, long continuous seams are better than skipped welds, which can leave gaps where sparks and ash escape.
  6. Add the base. Weld the base plate to the walls. Drill drain holes in it so that rainwater can escape, which reduces rust and water pooling.
  7. Add airflow and a grate. A few holes or slots near the bottom of the walls help airflow. A grate or raised standoffs lift the wood off the floor of the pit for better burning and protect the base from direct heat.
  8. Attach legs or a base frame. Keep air space below the pit, so heat does not scorch the ground or surface beneath. Make sure the legs are even and stable.
  9. Clean up. Grind spatter and sharp edges. Remove mill scale, oil and any markings from where you will paint.
  10. Finish. Apply high-temperature paint following its instructions, or leave the steel bare and let it develop a rust patina, if you prefer that look. Cure the paint properly, usually by burning a small first fire as the manufacturer directs.

Finishing and care

  • High-temperature paint will discolor and may burn off in the hottest areas. That is normal, and touching up is easy.
  • Bare steel will rust. Some people like that look, and a light coat of oil or a clear heat-resistant sealant can slow it.
  • Empty ashes after use and keep water from sitting inside, which speeds up rust. A cover helps.
  • Inspect welds from time to time. Repeated heating and cooling can crack weak welds (see why welds crack).

Common mistakes

  • Using steel that is too thin, which warps badly after a few fires
  • Welding galvanized or painted metal without removing the coating
  • Skipping drain holes, which leads to standing water and rust
  • Trapping heat under the pit, which damages the surface below
  • Placing the pit too near combustible surfaces

If you enjoy this build, try a welding cart next for more frame work, or browse more welding project ideas. For decorative treatment of steel, see welding as an art form.

The complete guide to projects and repairs

Welding Project Ideas for Beginners and Hobbyists
Read the guide

Keep exploring

Guides from other topics

All topics →